8.3 Menu structure
AUTO
ON
RESET
HAND
ON
OFF
1(1)
ON
ALARM
WARN.
Main Menu
Groups
0-** to 203-**
Group x
Selection
Parameter group
x-x* to x-x*
Group 203
Selection
Parameter group
203-0* to 203-8*
Group 0
Selection
Parameter group
0-0* to 0-8*
Parameter
Selection
Parameter
0-xx to 0-xx
Parameter
Selection
Parameter
0-70 to 0-89
Parameter
Selection
Parameter
0-01 to 0-08
TM07881
1
0-** Operation / Display
14-** Special Functions
27-** Cascade CTL Option
0-0* Basic Settings
14-0* Inverter Switching
27-0* Control & Status
0-1* Set-up Operations
14-1* Mains On/Off
27-1* Configuration
0-2* LCP Display
14-2* Reset Functions
27-2* Bandwidth Settings
0-4* LCP Keypad
14-3* Current Limit Ctrl.
27-3* Staging Speed
0-5* Copy/Save
14-4* Energy Optimising
27-4* Staging Settings
0-6* Password
14-5* Environment
27-5* Alternate Settings
0-7* Clock Settings
14-6* Auto Derate
27-6* Digital Inputs
1-** Load and Motor
14-8* Options
27-7* Connections
1-0* General Settings
14-9* Fault Settings
27-8* Advanced Settings
1-1* Motor Selection
15-** Drive Information
27-9* Readouts
1-1* VVC+ PM
15-0* Operating Data
29-** Water Application Functions
1-2* Motor Data
15-3* Alarm Log
29-0* Pipe Fill
1-3* Adv. Motor Data
15-4* Drive Identification
29-1* Deragging Function
1-5* Load Indep. Setting
15-6* Option Ident
29-2* Derag Power Tuning
1-6* Load Depen. Setting
15-8* Operating Data II
29-4* Pre/Post Lube
1-7* Start Adjustments
15-9* Parameter Info
30-** Special Features
1-8* Stop Adjustments
16-** Data Readouts
30-2* Adv. Start Adjust
1-9* Motor Temperature
16-0* General Status
35-** Sensor Input Option
2-** Brakes
16-1* Motor Status
35-0* Temp. Input Mode
2-0* DC-Brake
16-3* Drive Status
35-1* Temp. Input X48/4
2-1* Brake Energy Funct.
16-5* Ref. & Feedb.
35-2* Temp. Input X48/7
4-** Limits / Warnings
16-6* Inputs & Outputs
35-3* Temp. Input X48/10
4-1* Motor Limits
16-8* Fieldbus & FC Port
35-4* Analog Input X48/2
4-5* Adj. Warnings
16-9* Diagnosis Readouts
40-** Special Settings
4-6* Speed Bypass
18-** Info & Readouts
40-4* Extended. Alarm Log
5-** Digital In/Out
18-0* Maintenance Log
200 - Operation Settings
5-0* Digital I/O mode
18-3* Analog Readouts
200-0* Operation Settings
5-1* Digital Inputs
18-6* Inputs & Outputs 2
200-1* Setpoint Handling
5-3* Digital Outputs
20-** Drive Closed Loop
200-2* Proportional Pressure Setup
5-4* Relays
20-0* Feedback
200-4* Pump Setup
5-8* I/O Options
20-2* Feedback/Setpoint
200-5* Special Command Parameters
6-** Analog In/Out
20-8* PID Basic Settings
200-6* Setpoint Configuration Parameters
6-1* Analog Input 53
20-9* PID Controller
200-7* Configuration Command
Parameters
6-2* Analog Input 54
21-** Ext. Closed Loop
201- Key Functions
6-5* Analog Output 42
21-1* Ext. CL 1 Ref./Fb.
201-0* Limit Exceed
8-** Comm. and Options
21-2* Ext. CL 1 PID
201-1* Bearing Supervision
24
English (GB)
