Grundfos CRN 125-7 Скачать руководство пользователя страница 19

Страница: 19 / 38

5.9 Flange forces and torques

If not all loads reach the maximum permissible value stated in the tables below, one of these values may
exceed the normal limit. Contact Grundfos for further information.

Y-direction: Inlet or outlet
Z-direction: Direction of
chamber stack
X-direction: 90° from inlet or
outlet

TM040346

The following tables represent the values that apply according to the material quality.

Force limits for CR pumps

Flange

Force, Y-direction

[lbf (N)]

Force, Z-direction

[lbf (N)]

Force, X-direction

[lbf (N)]

4" ANSI (DN 100)

282 (1256)

228 (1013)

253 (1125)

6" ANSI (DN 150)

125, 155

422 (1875)

342 (1519)

380 (1688)

8" ANSI (DN 200)

185, 215, 255

465 (2513)

455 (2025)

506 (2250)

Force limits for CRN pumps

Flange

CRN

Force, Y-direction

[lbf (N)]

Force, Z-direction

[lbf (N)]

Force, X-direction

[lbf (N)]

4" ANSI (DN 100)

565 (2513)

455 (2025)

506 (2250)

6" ANSI (DN 150)

125, 155

843 (3750)

683 (3038)

759 (3375)

8" ANSI (DN 200)

185, 215, 255

1130 (5025)

910 (4050)

1012 (4500)

Torque limits for CR pumps

Flange

Torque, Y-direction

[lbf (N)]

Torque, Z-direction

[lbf (N)]

Torque, X-

direction

[lbf (N)]

4" ANSI (DN 100) 95

84 (375)

107 (475)

141 (625)

6" ANSI (DN 150) 125, 155

141 (625)

174 (775)

225 (1000)

8" ANSI (DN 200) 185, 215, 255

202 (900)

242 (1075)

309 (1375)

English (US)

Содержание CRN 125-7







































Результаты поиска

Содержание CRN 125-7

Отзывы:

Похожие инструкции для CRN 125-7

Бренды по названию

Популярные бренды

Grundfos CRN 125-7, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CRN 125-7

Отзывы:

Похожие инструкции для CRN 125-7

Бренды по названию

Популярные бренды