Grunbeck softliQ:SD Series Скачать руководство пользователя страница 55

Страница: 55 / 80

Cleaning, inspection, maintenance

55 | 80

-B

liQ

-SD

7.4

Maintenance

7.4.1

Semi-annual maintenance

In order to carry out the semi-annual maintenance, proceed as follows:

Check the soft water hardness (refer to chapter 6.6).

Check that there are sufficient salt tablets in the brine tank.

The level of salt tablets in the brine tank must always be higher than the
water level. The water level is normally approx. 1 cm above the sieve bottom.

Evaluate the salt consumption subject to the water volume consumed.

Check the salt condition (salt must not be lumpy).
Break up incrustations with a suitable tool.

Check the function of the water sensor by immersing the water sensor in water or
alternatively bridge it with a metallic object.

» The water sensor is working if the water softener issues a warning message after

30 seconds at the latest.

Содержание softliQ:SD Series

















































































Результаты поиска

Содержание softliQ:SD Series

Отзывы:

Похожие инструкции для softliQ:SD Series

Бренды по названию

Популярные бренды

Grunbeck softliQ:SD Series, Руководство по эксплуатации

Результаты поиска

Содержание softliQ:SD Series

Отзывы:

Похожие инструкции для softliQ:SD Series

Бренды по названию

Популярные бренды