Growcol GHyper 3000 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 52

Growcol GHyper 3000 Скачать руководство пользователя страница 19

15

5 Mounting Installation

5.1 Requirements for Mounting

•

Make sure there is no electrical connection before installation.

•

In order to avoid electric shock or other injury, make sure that holes will not
be drilled over any electricity or plumbing installations.

•

Always follow the instructions when moving and positioning the inverter.

•

Improper operation may cause injuries or serious wounds.

•

In the case of poor ventilation, the system performance may compromise.

5.1.1 Location Requirements

No direct sunlight

No rain exposure

No snow lay up

Direct sunlight

Rain exposure

Snow lay up

Select an optimal mounting location for safe operation, long service life and
expected performance. Please AVOIDE direct sunlight, rain exposure, snow laying
up during installation and operation. And DO NOT install the inverter in a place
where personnel are likely to come into contact with its enclosure and heat sinks
because these parts are extremely hot during operation.

«
...
17
18
19
20
21
...
»

Содержание GHyper 3000





















































Отзывы:

Нет отзывов