manualshive.com logo in svg

Grizzly G0948, Руководство пользователя

Поделиться
Скачать
Grizzly G0948 Скачать руководство пользователя страница 66

-64-

Model G0948 (Mfd. Since 08/21)

BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

Labels & Cosmetics

REF PART #

DESCRIPTION

REF PART #

DESCRIPTION

201

P0948201

MODEL NUMBER LABEL

207

P0948207

READ MANUAL LABEL

202

P0948202

GRIZZLY INDUSTRIAL LOGO LABEL

208

P0948208

MACHINE ID LABEL

203

P0948203

DISCONNECT POWER LABEL

209

P0948209

GRIZZLY.COM LABEL

204

P0948204

TOUCH-UP PAINT, GRIZZLY GREEN

210

P0948210

EYE/LUNG INJURY LABEL

205

P0948205

ELECTRICITY LABEL

211

P0948211

TOUCH-UP PAINT, GRIZZLY BEIGE

206

P0948206

DO NOT OPEN DOOR LABEL

grizzly.com

G0948

WARNING!

EYE/LUNG INJURY 

HAZARD!

Always wear safety 

glasses and a 

respirator when 

using this machine.

MODEL G0948

10" 1/2 HP BANDSAW

Specifications

WARNING!

To reduce risk of serious injury when using this machine:

  1.  Read and understand owner’s manual before operating.
  2.  Never touch moving blade. Keep hands out of blade path.
  3.  Always wear approved eye protection and respirator.
  4.  Only plug power cord into a grounded outlet.
  5.  Only remove jammed cutoff pieces when blade is stopped.
  6.  Use push stick or holding jig to cut small or narrow pieces.
  7.  Disconnect power before changing blades or adjusting saw.
  8.  Maintain adjustment of blade tension, tracking, and guides.
  9.  Keep upper guide adjusted to just clear the workpiece.
 10.  Hold workpiece firmly against table to maintain control.
 11.  Only run saw with wheel covers closed and all guards in place.
 12.  Never reach under table while blade is in motion.
 13.  Remove/secure loose clothing and long hair.
 14.  DO NOT expose to rain or use in wet locations.
 15.  Prevent unauthorized use by children or untrained users; 

restrict access or disable machine when unattended.

Motor: 1/2 HP, 120V, 1-Ph, 60Hz
Full Load Amp Draw: 3.5A
Blade Speed: 1520, 2620 FPM
Standard Blade Length: 72"
Blade Length Range: 71-1/2"–72-1/2"
Blade Width Range: 1/8"–1/2"
Max. Cutting Width Left of Blade: 9-3/4"
Max. Cutting Height: 6-1/8"
Table Size: 14-3/16" x 12-5/8"
Table Tilt: 0˚L ⁄ 45˚R
Weight: 69 lbs. 

Mfd. for Grizzly in China

Date

S/N

To reduce risk of death 

or serious injury, read 

manual BEFORE using 

machine.
To get a new manual, 

call (800) 523-4777 or 

go to www.grizzly.com.

WARNING!

INJURY/SHOCK 

HAZARD!

Disconnect power 

before adjustments, 

maintenance, or 

service.

INJURY HAZARD!

Do not open door 

while machine is 

connected to power 

or blade is in motion.

201

202

203

205

206

207

208

209

210

204

211

205

Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes 

off or becomes unreadable, the owner of this machine MUST replace it in the original location 

before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.

Содержание G0948





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды