Grizzly G0948 Скачать руководство пользователя страница 5

Страница: 5 / 68

Model G0948 (Mfd. Since 08/21)

-3-

Identification

Become familiar with the names and locations of the controls and features shown below to better understand
the instructions in this manual.

For Your Own Safety, Read Instruction Manual Before Operating Saw.

a) Wear eye protection.

b) Do not remove jammed cutoff pieces until blade has stopped.

c) Maintain proper adjustment of blade tension, blade guides, and thrust bearings.

d) Adjust upper blade guide to just clear workpiece.

e) Hold workpiece firmly against table.

Upper Wheel Cover

Blade Tension

Knob

Table Tilt

Lock Handle

Guide Post

Adjustment Knob

Guide Post

Lock Knob

Miter

Gauge

Lower Wheel

Cover

LED Work Light
ON/OFF Switch

ON/OFF

Paddle Switch

Fence Lock

Handle

Lower Wheel

Adjustment Hub

Tracking Knob

Lock Lever

Tracking

Knob

Dust Port

Stand

Fence

Guide Post

Fence

Rail

Table

Blade Guides

Work Light

Motor

Содержание G0948





































































Результаты поиска

Содержание G0948

Отзывы:

Бренды по названию

Популярные бренды

Grizzly G0948, Руководство пользователя

Результаты поиска

Содержание G0948

Отзывы:

Бренды по названию

Популярные бренды