Grizzly G0948 Скачать руководство пользователя страница 41

Страница: 41 / 68

Model G0948 (Mfd. Since 08/21)

-39-

Removing Blade

1. DISCONNECT MACHINE FROM POWER!

2. Release blade tension by rotating blade ten-

sion knob counterclockwise.

3. Adjust upper blade guide assembly all the

way up, move blade guides completely away
from blade, and remove table insert.

4. Remove fence rail.

5. Open upper and lower wheel covers.

6. Put on heavy leather gloves.

Removing/Installing

Blade

Disconnect bandsaw from

power BEFORE changing

blade. Serious personal

injury could occur if

machine is started during

this procedure.

LACERATION HAZARD!

Bandsaw blades are sharp

and difficult to handle.

Wear heavy leather gloves

while handling to reduce

the risk of being cut.

Figure 47. Example of removing blade.

Installing Blade

1. DISCONNECT MACHINE FROM POWER!

2. Slide blade through table slot, ensuring that

teeth are pointing down toward table.

Note: If the teeth will not point downward
in any orientation, the blade is inside out.
Remove the blade and twist it right-side out.

3. Slip blade over wheels while making sure it

is properly positioned between blade guards
and guides.

4. Tension blade (refer to Tensioning Blade on

Page 22 for details).

5. Adjust blade tracking (see Initial Blade

Tracking on Page 20).

6. Adjust upper/lower support bearings and

blade guides (refer to

Adjusting Blade

Support Bearings and Adjusting Blade

Guide Bearings on Pages 24–25).

7. Close wheel covers, and install table insert

and fence rail.

8. Make sure fence is parallel to miter slot and,

if necessary, adjust alignment (see

Page 28).

7. Slip blade off both wheels, slide it through

table slot (see

Figure 47), and remove it from

machine.

Items Needed

Qty

Heavy Leather Gloves ..................................1 Pr.
Hex Wrench 4mm .............................................. 1

Содержание G0948





































































Результаты поиска

Содержание G0948

Отзывы:

Бренды по названию

Популярные бренды

Grizzly G0948, Руководство пользователя

Результаты поиска

Содержание G0948

Отзывы:

Бренды по названию

Популярные бренды