Grizzly G0894 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 48

background image

Model G0894 (Mfd. Since 05/19)

-33-

SECTION 6: MAINTENANCE

For optimum performance from this machine, this
maintenance schedule must be strictly followed.

Ongoing
To minimize your risk of injury and maintain proper
machine operation, shut down the machine imme-
diately if you ever observe any of the items below,
and fix the problem before continuing operations:

•

Loose mounting bolts.

•

Damaged or dull cutter.

•

Clogged or dirty collet, spindle nut, or spindle
collet hole.

•

Blocked dust collection.

•

Worn or damaged wires.

•

Low or dirty water in coolant bucket.

•

Any other unsafe condition.

Weekly Maintenance
•

Clean cutter.

•

Check/adjust lubrication level in oiler.

•

Clean/vacuum dust buildup in T-slots.

•

Inspect spoilboard for defects and flatness.

Monthly Check
•

Check tubing and connections for coolant
system and oiler system.

•

Inspect wiring connections for loose wires.

Schedule

To reduce risk of shock or

accidental startup, always

disconnect machine from

power before adjustments,

maintenance, or service.

Cleaning the Model G0894 is relatively easy.
Vacuum excess wood chips and sawdust, and
wipe off the remaining dust with a dry cloth.

The G0894 ball screw bearings require regular
lubrication to perform at their highest potential.
There is an oiler system, located on the back of
the gantry, that pumps oil to these bearings.

Lubrication

Cleaning &

Protecting

Lube Type ............T27914 Way Oil or ISO 68 Oil

Lube Amount .........................................1 Pump

Lubrication Frequency ........ 8 hrs. of Operation

Oil Reservoir Max Capacity ....................... 1 qt.

The  G0894  spindle  motor  requires  a  constant
flow  of  coolant  to  prevent  overheating.  It  is
recommended that distilled water be used to pre-
vent  mineral  buildup  inside  the  system.  Monitor
water  level  and  cleanliness  regularly.  Replace
water if discolored or if debris is visible.

If machine is operated or stored in freezing tem-
peratures, anti-freeze should be added to coolant.

Coolant

Coolant Type ............................... Distilled Water

Coolant Amount ....................................... 4 gal.

Coolant Frequency .............. 8 hrs. of Operation

«
...
33
34
35
36
37
...
»

Содержание G0894

















































Отзывы:

Нет отзывов

Похожие инструкции для G0894

Бренд: GE Страницы: 50

Бренд: Makita Страницы: 2

Бренд: Lakeshore Страницы: 72

Бренд: Parkside Страницы: 78

Бренд: HOZAN Страницы: 2

Бренд: Metabo Страницы: 5

SPD1000X Series

Бренд: SIGLENT Страницы: 24

Бренд: Silverline Страницы: 2

Бренд: Gallagher Страницы: 22

Бренд: OEM Tools Страницы: 4

Бренд: MAIMAN ELECTRONICS Страницы: 24

Бренд: Radio Shack Страницы: 13

Бренд: Athena Power Страницы: 10

Бренд: SIRCHIE Страницы: 8

Бренд: ujk technology Страницы: 4

Бренд: TekPower Страницы: 4

Бренд: Facom Страницы: 20

Бренд: Westfalia Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды