Grizzly G0894 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 48

background image

Model G0894 (Mfd. Since 05/19)

-27-

Adjusting Axis

Positions Manually

Knowing how to manually control axis movement
is an essential part of operating the G0894. Axes
must be positioned manually whenever a work
origin is set.

Use axis movement buttons on controller (X+,
X-, Y+, Y-, Z+, and Z-) to move axes. See

Controller Functions on Page 5 for detailed
button descriptions.

Manual axis movement can be performed at two
speeds and in three motion modes: Continuous,
Step, and Distance.

Manual axis movement can move beyond

soft limit proximity switches, which can

damage the machine. Be aware of axis

locations during manual movement, and

be prepared to stop machine if axes move

unexpectedly.

1. Press HIGH/LOW to toggle between fast and

slow speeds.

2. Secure workpiece to spoilboard.

Note: Depending on the needs of the
workpiece and G-code, it could be appro-
priate to use additional hold-down clamps,
double-sided tape, or mount the workpiece
directly to the spoilboard with screws.

To surface using the mill plane operation:

1. Hold down RUN/PAUSE on controller, then

press HIGH/LOW and release buttons togeth-
er to open advanced processing menu.

2. Scroll to "Mill plane" and press OK.

3. Choose "Scan mill" or "Encircle mill" and

press OK. A list of operation parameters will
appear.

Note: A "Scan mill" operation runs back and
forth from one end of the defined workpiece
to the other. An "Encircle mill" operation runs
from the outside to the inside of the defined
workpiece.

4. Define operation parameters. Press RUN/

PAUSE to change a parameter and OK to
save. Distances are measured in millimeters.

— Scan Type changes the direction of the

operation.  For  scan  milling,  "X  Scan"
runs  back  and  forth  across  the  X-axis,
and "Y Scan" runs back and forth across
the Y-axis. For encircle milling, "AC" runs
counter  clockwise  around  the  workpiece
and  "C"  runs  clockwise  around  the
workpiece.

— Height and Width defines the size of the

area to be surfaced.

— Diameter defines the diameter of the sur-

facing tool used.

Items Needed

Qty

Spoilboard cutter or fly cutter ........................... 1

The G0894 can be used to surface a spoilboard
or workpiece, using the mill plane feature and
an appropriate cutter (see

Choosing Cutter on

Page 24).

Surfacing

Changing Axis Movement Speed

— Depth defines the total depth of material

removed. Z Step defines how much mate-
rial is removed per pass. For example,
a Depth of 1 and Z Step of 0.25 would
remove 1mm of material over four passes.

5. Press OK after all parameters have been

saved to start the mill plane operation.

«
...
27
28
29
30
31
...
»

Содержание G0894

















































Отзывы:

Нет отзывов

Похожие инструкции для G0894

Бренд: Vector Страницы: 6

Бренд: National Flooring Equipment Страницы: 23

Бренд: Parkside Performance Страницы: 134

Color Block PSU-05B

Бренд: Chroma Страницы: 2

Бренд: Lumberjack Страницы: 14

Бренд: Pulsar Страницы: 2

Бренд: Akyga Страницы: 4

MAG-8200 Series

Бренд: Magna-Matic Страницы: 10

Бренд: B&B Страницы: 3

Бренд: ATI Technologies Страницы: 38

Бренд: Ferm Страницы: 120

Gardtec 500 series

Бренд: GARDINER TECHNOLOGY Страницы: 40

MICRO-Router MOF

Бренд: Proxxon Страницы: 16

Бренд: Draper Страницы: 12

Бренд: YOKOGAWA Страницы: 21

Digital Knight DK16

Бренд: Geo Knight Страницы: 25

Accurate Power Generator

Бренд: Clearaudio Страницы: 10

Бренд: Slime Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды