Grizzly G0894 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 48

background image

Model G0894 (Mfd. Since 05/19)

-21-

Test Run

Once assembly is complete, test run the machine
to ensure it is properly connected to power and
safety components are functioning correctly.

If you find an unusual problem during the test run,
immediately stop the machine, disconnect it from
power, and fix the problem BEFORE operating the
machine again. The

Troubleshooting table in the

SERVICE section of this manual can help.

DO NOT start machine until all preceding

setup instructions have been performed.

Operating an improperly set up machine

may result in malfunction or unexpect-

ed results that can lead to serious injury,

death, or machine/property damage.

Serious injury or death can result from

using this machine BEFORE understanding

its controls and related safety information.

DO NOT operate, or allow others to operate,

machine until the information is understood.

6. Press ON button on machine to turn machine

ON.

7. Verify machine parameters as shown on

Page 22.

8. Press ON/OFF button on controller to start

spindle motor. Verify spindle starts and runs
smoothly without any unusual problems or
noises. Press ON/OFF to stop spindle motor.

9. Press HOME button on controller. Verify that

each axis motor operates smoothly and that
all axes move to machine zero.

10. Press E-STOP button on machine to turn

machine

OFF.

11. WITHOUT resetting E-STOP button, try to

start machine by pressing the ON button. The
machine should not start.

— If the machine does not start, the safety

feature of the E-STOP button is working
correctly. Congratulations! The Test Run
is complete.

— If the machine does start, immediately turn

it

OFF and disconnect power. The safety

feature of the E-STOP button is NOT
working properly and must be replaced
before further using the machine.

To test run machine:

1. Clear all setup tools away from machine.

2. Ensure controller and cooling pump are con-

nected to machine.

3. Press E-STOP button.

4. Connect machine to power by inserting power

cord plug into a matching receptacle.

Figure 18. Resetting the E-STOP button.

The test run consists of verifying the following: 1)
the spindle motor powers up and runs correctly,
2) the axes motors run correctly and the machine
properly homes, and 3) the E-STOP button safety
feature functions properly.

5. Twist E-STOP button clockwise until it springs

out (see

Figure 18). This resets the switch so

the machine can start.

«
...
21
22
23
24
25
...
»

Содержание G0894

















































Отзывы:

Нет отзывов

Похожие инструкции для G0894

Бренд: Makita Страницы: 10

Бренд: Makita Страницы: 9

Бренд: Makita Страницы: 48

Бренд: Makita Страницы: 8

Бренд: Makita Страницы: 11

Бренд: Makita Страницы: 5

Бренд: Makita Страницы: 2

Бренд: Makita Страницы: 15

Бренд: Makita Страницы: 2

Бренд: Makita Страницы: 2

Бренд: Makita Страницы: 14

Бренд: Makita Страницы: 2

Бренд: Makita Страницы: 20

Бренд: Makita Страницы: 9

Бренд: EGAmaster Страницы: 10

Boostamatic 4000

Бренд: Stuart Страницы: 20

Бренд: Microtec Страницы: 6

Бренд: Wacker Neuson Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды