Grizzly G0866 Скачать руководство пользователя страница 32

Страница: 32 / 100

-30-

Model G0866 (Mfd. Since 11/18)

— If sanding belts and conveyer belt do not

come to a complete stop, immediately dis-
connect power. The safety feature of the
EMERGENCY STOP! plate is NOT work-
ing properly. This must be fixed before
machine can be used further.

— If sanding belts and conveyer belt do come

to a complete stop, the safety feature of
the EMERGENCY STOP! plate is working
correctly. Congratulations! The Test Run
is complete.

Figure 47. EMERGENCY STOP! plate location.

EMERGENCY STOP!

Plate

You MUST verify that table moves in expect-

ed direction according to buttons pressed

on control panel, otherwise all controls will

function in reverse. Conveyer belt and sand-

ing belts MUST rotate in the correct direc-

tion or serious personal injury could occur.

— If the machine does start, immediately

turn it

OFF and disconnect power. The

safety feature of the Emergency Stop but-
ton is NOT working properly and must be
replaced before further using the machine.

10. Repeat Steps 7–9 with the rear sanding belt

start button and then the conveyor belt start
button to test rear main motor and feed motor
(see

Figure 46). Both should run smoothly

and without unusual problems or noises. Belt
should move away from operator and toward
sanding drums while feed motor is running.

11. Reset Emergency Stop button.

12. Press sanding belt and conveyor belt start

buttons, then press EMERGENCY STOP!
plate (see

Figure 47).

Figure 46. Control panel controls.

Rear Sanding Belt

Start Button

Front Sanding Belt

Start Button

Conveyer Belt

Start Button

7. Press front sanding belt start button to turn

front main motor

ON (see Figure 46). Verify

motor starts up and runs smoothly without
any unusual problems or noises.

— If table moves in same direction as but-

ton description, power supply polarity is
correct.

— If table moves in opposite direction to

arrow  on  button,  stop  machine  and
DISCONNECT  FROM  POWER.  Phase
polarity  of  incoming  power  is  reversed.
Refer  to

Correcting Phase Polarity on

Page 28 before proceeding with remain-
der of

Test Run.

8. Press Emergency Stop button to turn machine

OFF.

9. WITHOUT resetting Emergency Stop button,

try to start machine by pressing front sand-
ing belt start button. The machine should not
start.

— If the machine does not start, the safety

feature of the Emergency Stop button is
working correctly. Proceed to next step.

Содержание G0866





































































































Результаты поиска

Содержание G0866

Отзывы:

Grizzly G0866, Руководство пользователя, Страница: 32 / 100

Результаты поиска

Содержание G0866

Отзывы: