Grizzly G0677 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 96

background image

G0677 24" Planer/Sander

-49-

Pressure Rollers

Figure 64. Infeed pressure roller adjustment

locations.

6. Connect the machine to the power source

and  make  note  of  the  reading  on  the  digi-
tal  display.  Then  manually  lower  the  table
0.035".  This  is  how  much  lower  than  the
sanding drum the infeed pressure roller and
outfeed pressure rollers should be.

7. DISCONNECT THE PLANER/SANDER

FROM THE POWER SOURCE!

8. Loosen the infeed pressure roller lock nuts

(

Figure 64) on the infeed pressure roller.

Turn the adjustment studs (

Figure 64) to

lower the infeed pressure roller until it just
touches the boar

ds.

Note: DO NOT continue to lower the roller

beyond this point.

Right Side View

Left Side View

Adjustment

Stud

Roller

Lock

Nuts

Adjustment

Stud

Roller

Lock

Nuts

2. DISCONNECT THE PLANER/SANDER

FROM THE POWER SOURCE

!

3.

Raise the cutterhead up to the 2mm mark so
it does not interfere with your adjustments in
the following steps.

4. Open the upper left access door and remove

the sanding belt.

5.

Move the sanding drum by hand and

manu-

ally raise the table until you hear the rubber
drum just contact the surface of the wood.
DO NOT continue to raise the table beyond
this point.

Figure 63. 2x4s placed on feed belt under

sanding drum.

To adjust the pressure rollers:

1. Plane a 6' long 2x4 to a uniform thickness

and cut it in half. Place one board along the
length of the feed belt on the right-hand side
and place the other board on the left-hand
side, as shown in

Figure 63

.

The pressure rollers have been adjusted at the
factory and should require no further attention.

Ideally the pressure rollers should be positioned
slightly lower than the sanding drum. However, we
recommend verifying this setting.

Factory Settings
Infeed & Outfeed Pressure Roller Setting Below
Sanding Drum ........................................... 0.035"

T

ools Needed

Qty

6' Long 2x4 Cut in Half ...................................... 1
Wrench 14mm ................................................... 1

9. Tighten the roller lock nuts.

10. Repeat

Steps 7-8

in a similar manner to

lower the outfeed pressure rollers until they
just touch the boards, then tighten the roller
lock nuts and recheck your settings.

Infeed

Roller

Infeed

Roller

Outfeed

Rollers

Outfeed

Rollers

«
...
49
50
51
52
53
...
»

Содержание G0677

































































































Отзывы:

Нет отзывов

Похожие инструкции для G0677

Бренд: TAD Страницы: 120

Бренд: NAD Страницы: 44

Бренд: Magnavox Страницы: 21

Бренд: Magnavox Страницы: 2

SpongeBob Squarepants SB280

Бренд: Emerson Страницы: 19

SpongeBob Squarepants SB250

Бренд: Emerson Страницы: 22

SpongeBob SquarePants SB260

Бренд: Emerson Страницы: 16

Бренд: Emerson Страницы: 16

SpongeBob Squarepants SB250A

Бренд: Emerson Страницы: 22

Бренд: Emerson Страницы: 23

Бренд: Emerson Страницы: 20

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 27

CFD-V177 - Cd Radio Cassette-corder

Бренд: Sony Страницы: 2

CFD-V17 - Cd Radio Cassette-corder

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 44

CFD-S550 - Cd Radio Cassette-corder

Бренд: Sony Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды