Grizzly G0677 Скачать руководство пользователя | Manualshive

Страница: 44 / 96

background image

-42-

G0677 24" Planer/Sander

Table Calibration

The  digital  thickness  gauge  is  calibrated  at  the
factory,  but  we  recommend  you  verify  its  accu-
racy.  This  can  be  done  by  feeding  a  test  board
through  the  machine  and  measuring  it  in  many
locations  on  both  sides  along  the  length,  then
calibrating the digital display to match the average
measured thickness of the workpiece.

Tools Needed

Qty

Test Board ......................................................... 1
Set of Calipers ................................................... 1

Calibrating Digital Thickness Scale

1. Run the test board though the planer/sander

three to four times to plane and sand it.

2. Turn the board over, and repeat Step 2.

3. Measure the thickness at various points

around the board using a set of calipers.

4. Without moving the table height, enter the

numerical measurement from

Step 3

into the

digital key pad on the control panel.

Note:

The average thickness of the sanded

wood should now be flashing on the digital
read-out.

5. Press and hold the Set key

until the dis-

play stops flashing. The machine is now cor-
rectly calibrated.

Table Limit Switches

The table limit switches prevent the table lift motor
from driving the table into the sanding drum.
Periodically check and adjust (if required) the
table stop switches to protect the feed belt.

Tools Needed

Qty

Wrench or Socket 10mm ................................... 1

To check and adjust table limit switches:

1. Connect the planer/sander to power and air.

2. With the sanding belt motor OFF, use the up

and down buttons to test the table.

3. Make sure the switches shut the table lift

motor

OFF

when the table is at the minimum

(

1

⁄

8

") and maximum distance (6") from the

sanding drum.

—If the table lift motor does not shut

OFF

when the table reaches the minimum and
maximum distances from the sanding drum,
the limit switches need to be adjusted.
Proceed to

Step 4.

4. Push the down arrow key

and lower the

table until there are six inches between the
sanding drum and the feed belt table sur-
face.

5. Loosen the mounting bolts for the table-down

limit switch and slide the switch so the switch
plunger depresses against the stop block and
you hear the switch click (see

Figure 47).

Figure 47. Table limit switches.

Stop Block

Table Up

Limit Switch

Table Down
Limit Switch

«
...
42
43
44
45
46
...
»

Содержание G0677

































































































Отзывы:

Нет отзывов

Похожие инструкции для G0677

Бренд: Jensen Страницы: 8

Бренд: Jensen Страницы: 7

Бренд: Denon Страницы: 58

Бренд: Parasound Страницы: 2

Бренд: Virutex Страницы: 24

Бренд: Goldmund Страницы: 13

Super Tuner IIID DEH-P4100

Бренд: Pioneer Страницы: 6

Бренд: Pioneer Страницы: 19

Super Tuner III D DEH-P4550

Бренд: Pioneer Страницы: 8

Super Tunet IIID DEH-16

Бренд: Pioneer Страницы: 25

Бренд: Pioneer Страницы: 11

XDV-M8137ZT-91/UC

Бренд: Pioneer Страницы: 38

Бренд: Pioneer Страницы: 44

Бренд: Pioneer Страницы: 20

Бренд: Pioneer Страницы: 57

SUPERTUNER III D DEH-P2650

Бренд: Pioneer Страницы: 70

Бренд: Pioneer Страницы: 52

SUPERTUNER III D DEH-P2650

Бренд: Pioneer Страницы: 94

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды