Grizzly G0677 Скачать руководство пользователя | Manualshive

Страница: 39 / 96

background image

G0677 24" Planer/Sander

-37-

Cleaning Sanding

Belts

To increase the working life of your sanding belts,
clean them whenever they decrease in perfor-
mance due to heavy loading. Use a Model H2845
Pro-Stik

®

Cleaning Pad as shown in

Figure 39 in

Accessories on Page 34.

To clean the belts:

1. DISCONNECT THE PLANER/SANDER

FROM THE POWER SOURCE!

2. Open the upper left access door, loosen the

cutterhead lock lever, move the cutterhead
assembly all the way up—so the cutterhead
will not cut the cleaning pad—then lock it in
place.

3. Set your table to the thickness of the cleaning

pad.

4. Connect power, then run the pad through the

sander two or three times. DO NOT take too
deep of a cut—the belt should barely touch
the cleaning pad!

5. Reset the cutterhead to the 0mm position

after you clean the sanding belt.

Cleaning Feed Belt

Vacuum  or  sweep  dust  off  the  feed  belt  with
compressed  air.  Use  a  diluted  solution  of  mild
dish cleaning soap and water with a clean rag to
remove  wood  resin  from  the  belt.  Do  NOT  use
solvent cleaners or harsh chemicals.

Feed Belt Gear Box

Lubricant

Frequency

Qty

80-90 Wt. Gear
Oil or ISO-VG
320 Oil

After First 100
Hours, then
Every 2500
Hours.

As Needed
to Fill Above
Sight Glass

Replace the feed belt gear box oil (

Figure 44). We

recommend 80-90 Wt. gear oil or ISO-VG320 oil.

To replace the feed belt gear box oil:

1. With the oil and gear box warm, remove the

fill plug (

Figure 44), remove the drain plug,

drain the oil, and re-install the drain plug.

2. Add new oil and re-install the fill plug.

Figure 44. Lubricating gear box.

Drain Plug

Fill

Plug

«
...
37
38
39
40
41
...
»

Содержание G0677

































































































Отзывы:

Нет отзывов

Похожие инструкции для G0677

Бренд: Nakamichi Страницы: 62

Бренд: Tevion Страницы: 6

Бренд: Parkside Страницы: 184

Бренд: Baileigh Industrial Страницы: 60

Бренд: Advance Paris Страницы: 20

Бренд: Parkside Страницы: 87

CHX1500 - CD Changer

Бренд: JVC Страницы: 65

CFD-980 Operating Instructions (English, Español)

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 6

Бренд: Sony Страницы: 4

CFD-C1000 - Boombox With Cd

Бренд: Sony Страницы: 20

Бренд: Sony Страницы: 14

Бренд: Sony Страницы: 32

CFD-C1000 - Boombox With Cd

Бренд: Sony Страницы: 36

Бренд: Sony Страницы: 15

Бренд: Sony Страницы: 15

Бренд: Sony Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды