Grizzly G0677 Скачать руководство пользователя | Manualshive

Страница: 36 / 96

background image

-34-

G0677 24" Planer/Sander

SECTION 5: ACCESSORIES

ACCESSORIES

Figure 39. Sanding belt cleaning pad.

H2845 Cleaning Pads
Cleaning pads are the perfect accessory for wide
belt sanders. Simply set the conveyor table to
height and feed the pad through to “unload” a dirty
sanding belt. Regular cleaning greatly increases
the lifespan of sanding belts. Check with the cur-
rent Grizzly catalog or

www.grizzly.com for more

details.

H3741 30 HP Rotary Phase Converter
Add 3-phase, multi-motor capability to your single-
phase electrical supply. Operate single or multiple
motors,  transformers,  and  resistance  loads  at
100%  power  and  95%  efficiency  while  saving
big  dollars  at  cheaply  metered,  single-phase
electrical  rates.  Complete  step-by-step  instruc-
tions  are  furnished  along  with  complete  wire
and fusing requirements for various motor loads.
Each  model  operates  up  to  twice  its  nameplate
rating  in  a  mixed-motor  load.  On  heavily  loaded
or  hard-start  applications,  such  as  high-speed
geared-head  lathes  and  air  conditioning  com-
pressors,  the  nameplate  rating  of  the  converter
you  choose  should  be  2  to  3  times  the  HP  of
the  most  heavily  loaded  motor.  See  the  individ-
ual  3-phase  machine  pages  for  phase  converter
recommendations.  For  application  assistance,
please  call  our  technical  support  at  (570)  546-
9663.

T20796—Indexable Carbide Inserts for Model

G0677

T21277—Front Hood for Model G0677
This dust hood allows you to replace the included
ports to consolidate dust collection hose connec-
tions. Each hood replaces 2 of the standard dust
ports. Buy 2 if replacing all the dust ports included
with the machine.

Figure 38. Rotary phase converter.

US-Made Sanding Belts for Model G0677
25"W x 60"L:

Single Pack

— G8675 60 Grit

— G8676 80 Grit

— G8677 100 Grit

— G8678 120 Grit

— G8679 150 Grit

3-Pack

— H8810 60 Grit

— H8812 80 Grit

— H8813 100 Grit

— H8814 120 Grit

— H8815 150 Grit

H9553—Wide-Belt Sander Hood
This dust hood is made to fit over the multiple 4"
dust ports on the Model G0677 planer/sander.
The base has a 1

1

⁄

2

" flange on all sides for mount-

ing to the sander. Port has rolled end that con-
nects to similarly sized pipe and fittings.

«
...
34
35
36
37
38
...
»

Содержание G0677

































































































Отзывы:

Нет отзывов

Похожие инструкции для G0677

Бренд: auna multimedia Страницы: 10

Бренд: Parkside Страницы: 210

Бренд: NAD Страницы: 20

Бренд: NAD Страницы: 56

Бренд: Hafco Woodmaster Страницы: 24

Бренд: Goodmans Страницы: 20

Бренд: RCA Страницы: 2

Бренд: ALDI Страницы: 28

Бренд: Meister Страницы: 92

Бренд: US Blaster Europe Страницы: 24

Бренд: Konig Страницы: 55

Sheartec:II PXl16

Бренд: laguna Страницы: 48

Бренд: Oliver Страницы: 65

Бренд: Maktec Страницы: 48

Бренд: Teac Страницы: 16

Бренд: Teac Страницы: 6

Бренд: Gröne Страницы: 148

Бренд: Hitachi Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды