Grizzly G0677 Скачать руководство пользователя

Страница: 23 / 96

G0677 24" Planer/Sander

-21-

To check the feed belt gear oil:

1. Check the sight glass shown on the back

of the gear box with a mirror, as shown in

Figure 21, to make sure gear oil is present.

Figure 21. Sight glass location on gear box.

2. If the gear box oil level is below the sight

glass level, follow the steps on

Page 37 to

refill the oil.

Sight Glass

Gear Box Oil

It is critical that you make sure there is oil in the
feed belt gear box before proceeding with the
test run. Refer to the

Lubrication instructions on

Page 37 for more details on which type of oil to
use, how much to use, and where to put it.

GEARBOX MUST

BE FILLED WITH OIL!

OIL MAY NOT BE SHIPPED WITH MACHINE!

You MUST add oil where needed

before operating.

Requires ISO-VG320

or 90 Weight Gear Oil

Gear Box

Breather Pin

The Model G0677 is shipped with a breather seal-
ing pin installed in the fill plug for the feed belt
gear box.

Remove this pin before using your machine (see

Figure 22); otherwise, the gear oil will expand
with heat and the seals in the gear box may leak
due to the pressure buildup.

You may want to keep this pin if you plan on stor-
ing your machine for a long period of time.

Figure 22. Breather sealing pin removed.

Breather Pin

Removed

Vented Fill

Plug

Vented Fill

Plug

Содержание G0677

































































































Результаты поиска

Содержание G0677

Отзывы:

Похожие инструкции для G0677

Бренды по названию

Популярные бренды

Grizzly G0677, Руководство пользователя

Результаты поиска

Содержание G0677

Отзывы:

Похожие инструкции для G0677

Бренды по названию

Популярные бренды