Grizzly G0677 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 96

background image

-18-

G0677 24" Planer/Sander

Air Hose

To install the air line:

1. Connect the air inlet (Figure 15

)

on the regu-

lator to a compressed air line.

Figure 15. Air hose attached to regulator.

Regulator

Knob

Air Inlet

2. Make sure the red ON/OFF handle on the

regulator is in the

open

position.

3. Lift the regulator knob (Figure

s

15

&

16) and

rotate it until the gauge reads 75 PSI.

Note: Rotate the knob clockwise to increase
the air pressure and counterclockwise to
lower the air pressure.

4. Push the knob down until it snaps to lock it.

Figure 16. Regulator knob.

Lock

Unlock

Decrease

Increase

Dust Collection

An  efficient  and  clean  dust  collection  system  is
essential  to  the  proper  function  of  the  planer/
sander.  Ensuring  a  healthy  work  environment  is
also  dependent  upon  cleaning  and  maintaining
your dust collection system. We recommend con-
necting this planer/sander to a cyclone dust col-
lector rather than a bag type dust collector, since
a cyclone will handle fine dust particles better and
experience fewer clogging problems.

DO NOT operate this machine without an

adequate dust collection system and a res-

pirator. This machine creates substantial

amounts of wood dust while operating.

Failure to use a dust collection system can

result in short and long-term respiratory ill-

ness.

Figure 17. Example of dust collection hose

attached to dust port.

Using 5" hose clamps, secure the hoses from
your dust collection system to the pre-installed
dust ports.

Hose Clamp

Air ON/OFF

Lever (Open

Position)

Recommended CFM @ Machine: 2500 CFM
Do not confuse this CFM recommendation with
the rating of the dust collector. To determine the
CFM at the dust port, you must consider these
variables: (1) CFM rating of the dust collector,
(2) hose type and length between the dust col-
lector and the machine, (3) number of branches
or wyes, and (4) amount of other open lines
throughout the system. Explaining how to cal-
culate these variables is beyond the scope of
this manual. Consult an expert or purchase a
good dust collection "how-to" book.

«
...
18
19
20
21
22
...
»

Содержание G0677

































































































Отзывы:

Нет отзывов

Похожие инструкции для G0677

Бренд: XINDAK Страницы: 13

Бренд: Pronomic Страницы: 11

Бренд: Exposure Страницы: 2

Бренд: Vextra Страницы: 1

Бренд: Festool Страницы: 62

Бренд: Harman Kardon Страницы: 67

Бренд: Quest Engineering Страницы: 9

Бренд: Baileigh Industrial Страницы: 48

Бренд: DAPAudio Страницы: 14

Бренд: Tascam Страницы: 32

Бренд: Tascam Страницы: 48

Бренд: Clatronic Страницы: 46

Бренд: Bosch Страницы: 86

GHO 40-82 C Professional

Бренд: Bosch Страницы: 231

Бренд: Bosch Страницы: 64

Бренд: Bosch Страницы: 48

GHO 6500 Professional

Бренд: Bosch Страницы: 210

Бренд: Bosch Страницы: 107

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды