Grizzly G0677 Скачать руководство пользователя | Manualshive

Страница: 10 / 96

background image

-8-

G0677 24" Planer/Sander

Safety Instructions for Machinery

For Your Own Safety, Read Instruction

Manual Before Operating this Machine

The purpose of safety symbols is to attract your attention to possible hazardous conditions. This

manual uses a series of symbols and signal words intended to convey the level of importance

of the safety messages. The progression of symbols is described below. Remember that safety

messages by themselves do not eliminate danger and are not a substitute for proper accident

prevention measures.

Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury. It may also be used to alert
against unsafe practices.

Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.

Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.

This symbol is used to alert the user to useful information about
proper operation of the machine.

NOTICE

WEARING PROPER APPAREL. Do not wear

clothing, apparel, or jewelry that can become

entangled in moving parts. Always tie back or

cover long hair. Wear non-slip footwear to avoid

accidental slips which could cause a loss of

workpiece control.

HEARING PROTECTION. Always wear hear-

ing protection when operating or observiing loud

machinery. Extended exposure to this noise

without hearing protection can cause permanent

hearing loss.

MENTAL ALERTNESS. Be mentally alert when

running machinery. Never operate under the

influence of drugs or alcohol, when tired, or when

distracted.

OWNER’S MANUAL. Read and understand
this owner’s manual BEFORE using machine.
Untrained users can be seriously hurt.

EYE PROTECTION. Always wear ANSI-

approved safety glasses or a face shield when

operating or observing machinery. to reduce

the risk of eye injury or blindness from fly-

ing particles Everyday eyeglasses are not

approved safety glasses.

HAzARDOUS DUST. Dust created while using
machinery may cause cancer, birth defects,
or long-term respiratory damage. Be aware of
dust hazards associated with each workpiece
material, and always wear a NIOSH-approved
respirator to reduce your risk.

Safety Instructions for Machinery

SECTION 1: SAFETY

«
...
8
9
10
11
12
...
»

Содержание G0677

































































































Отзывы:

Нет отзывов

Похожие инструкции для G0677

Бренд: Tascam Страницы: 39

Бренд: Tascam Страницы: 28

Бренд: M&S Systems Страницы: 12

Бренд: Panasonic Страницы: 4

CXDP88U - AUTO CD CHANGER

Бренд: Panasonic Страницы: 27

Бренд: Panasonic Страницы: 19

Бренд: Panasonic Страницы: 20

CX-DP610 Operating

Бренд: Panasonic Страницы: 36

Бренд: Panasonic Страницы: 44

CX-DP88 Operating

Бренд: Panasonic Страницы: 48

Бренд: Panasonic Страницы: 66

Бренд: Panasonic Страницы: 69

CX-DH801U - Car Audio - DVD

Бренд: Panasonic Страницы: 82

Бренд: Panasonic Страницы: 96

Бренд: Panasonic Страницы: 126

Diga DMR-BCT720

Бренд: Panasonic Страницы: 128

Бренд: Panasonic Страницы: 121

Бренд: Philips Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды