Grizzly EXTREME G0513X2 Скачать руководство пользователя

Страница: 86 / 100

-84-

G0513 Series Bandsaws (Mfd. Since 08/22)

BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes

off or becomes unreadable, the owner of this machine MUST replace it in the original location

before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.

REF

PART #

DESCRIPTION

REF PART #

DESCRIPTION

177V2 P0513177V2 MACHINE ID LABEL V2.07.18

186

P0513186

MODEL NUMBER LABEL

178

P0513178

ELECTRICITY LABEL

187

P0513187

TOUCH-UP PAINT, GRIZZLY GREEN

179

P0513179

GLASSES/RESPIRATOR LABEL

188

P0513188

TOUCH-UP PAINT, LIGHT GRAY

180

P0513180

READ MANUAL LABEL

189

P0513189

GUIDE POST ADJUST LABEL

181

P0513181

DOOR WARNING LABEL

191

P0513191

BLADE TENSION SCALE LABEL

183

P0513183

DISCONNECT POWER LABEL

195

P0513195

GUIDE POST LOCK LABEL

184

P0513184

GRIZZLY NAMEPLATE-SMALL

197

P0513197

GRIZZLY.COM LABEL

185

P0513185

SAW TENSION LABEL

G0513 Labels

181

184

186

177V2

179

180

188

187

• 1:1 Sizing (Labels are
actual size)
• Labels must be made of
oil-resistant material

DO NOT REPRODUCE OR CHANGE THIS ARTWORK

Grizzly will not accept labels changed without approval.

artwork changes are required, contact us immediately at [email protected].

grizzly.com

***

COLOR CODES

GRIZZLY GREEN

PANTONE 568C

DANGER

PANTONE 485 C or RAL 3001

PANTONE 151 C or RAL 2005

WARNING

GRIZZLY LOGO RED

PANTONE 711C or RAL 3020

Note:

Labels marked with ### must have individual

letters/numbers. DO NOT print with clear background.

• Scale= 1:1

(unless otherwise noted)

• Labels MUST be made of

chemical-resistant material

G0513 Machine Labels

(08/29/18)

Note:

Labels marked *** have changed since last sent.

###

grizzly.com

MODEL G0513

17" 2 HP BANDSAW

Motor: 2 HP, 110V/220V, 1-PH, 60 Hz
Motor Prewired: 220V
Amp Draw: 10A at 220V; 20A at 110V
Table Size: 17" x 17"
Blade Speeds: 1700 & 3500 FPM
Blade Length: 131-1/2"
Blade Width Range: 1/8" – 1"
Max. Cutting Width Left of Blade: 16-1/4"
Max. Cutting Height: 12-1/8"
Table Tilt: 10˚L ⁄ 45˚R
Weight: 266 lbs.

Specifications

Date

Mfd. for Grizzly in Taiwan

To reduce risk of serious injury when using this machine:

  1. Read & understand owner’s manual before operating.
  2.  Never touch moving blade—keep hands out of blade path.
  3. Always wear approved eye protection and respirator.
  4.  Only remove jammed cutoff pieces when blade is stopped.
  5.  Use push stick or holding jig to cut small or narrow pieces.
  6.  Disconnect power before changing blades or adjusting.
  7.  Maintain adjustment of blade tension, tracking, & guides.
  8.  Keep upper guide adjusted to just clear the workpiece.
  9.  Hold workpiece firmly against table to maintain control.
10.  Only run saw with wheel covers closed & all guards in place.
11.  Never reach under table while blade is in motion.
12.  Secure/remove loose clothing and long hair.
13.  DO NOT expose to rain or use in wet locations.
14.  DO NOT operate under influence of drugs or alcohol.
15.  Prevent unauthorized use by children or untrained users;

restrict access or disable machine when unattended.

FOR GRIZZLY MACHINES ONLY!

DO NOT REPRODUCE OR CHANGE THIS ARTWORK

WITHOUT WRITTEN APPROVAL!

Grizzly will not accept labels changed without approval.

artwork changes are required, contact us immediately at

[email protected]

G0513

178

Model G8588

185

MODEL G0513

17" 2 HP BANDSAW

Specifications

Date

Mfd. for Grizzly in Taiwan

To reduce risk of serious injury when using this machine:

restrict access or disable machine when unattended.

G0513

***

COLOR CODES

DANGER

PANTONE 485 C or RAL 3001

Note:

Labels marked with ### must have individual

letters/numbers. DO NOT print with clear background.

• Scale= 1:1

(unless otherwise noted)

• Labels MUST be made of

chemical-resistant material

G0513 Machine Labels

(08/29/18)

Note:

Labels marked *** have changed since last sent.

178

181

189

G0513 Series

Generic Labels

(7/12/13)

• 1:1 Sizing (Labels are
actual size)
• Labels must be made of
oil-resistant material

FOR GRIZZLY MACHINES ONLY!

DO NOT REPRODUCE OR CHANGE THIS ARTWORK

WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval.

artwork changes are required, contact us immediately at [email protected].

To reduce risk of death

or serious injury, read

manual BEFORE using

machine.
To get a new manual,

call (800) 523-4777 or

go to www.grizzly.com.

WARNING!

EYE/LUNG INJURY

HAZARD!

Always wear safety

glasses and a

respirator when

using this machine.

INJURY/SHOCK

HAZARD!

Disconnect power

before adjustments,

maintenance, or

service.

INJURY HAZARD!
Do not open door
while machine is
connected to power
or blade is in motion.

183

G0513 Series

Generic Labels

(7/12/13)

• 1:1 Sizing (Labels are
actual size)
• Labels must be made of
oil-resistant material

FOR GRIZZLY MACHINES ONLY!

DO NOT REPRODUCE OR CHANGE THIS ARTWORK

WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval.

artwork changes are required, contact us immediately at [email protected].

To reduce risk of death

or serious injury, read

manual BEFORE using

machine.
To get a new manual,

call (800) 523-4777 or

go to www.grizzly.com.

WARNING!

EYE/LUNG INJURY

HAZARD!

Always wear safety

glasses and a

respirator when

using this machine.

INJURY/SHOCK

HAZARD!

Disconnect power

before adjustments,

maintenance, or

service.

INJURY HAZARD!
Do not open door
while machine is
connected to power
or blade is in motion.

G0513 Series

Generic Labels

• 1:1 Sizing (Labels are
actual size)
• Labels must be made of
oil-resistant material

DO NOT REPRODUCE OR CHANGE THIS ARTWORK

Grizzly will not accept labels changed without approval.

artwork changes are required, contact us immediately at [email protected].

G0513 Series

Generic Labels

(7/12/13)

• 1:1 Sizing (Labels are
actual size)
• Labels must be made of
oil-resistant material

FOR GRIZZLY MACHINES ONLY!

DO NOT REPRODUCE OR CHANGE THIS ARTWORK

WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval.

artwork changes are required, contact us immediately at [email protected].

To reduce risk of death

or serious injury, read

manual BEFORE using

machine.
To get a new manual,

call (800) 523-4777 or

go to www.grizzly.com.

WARNING!

EYE/LUNG INJURY

HAZARD!

Always wear safety

glasses and a

respirator when

using this machine.

INJURY/SHOCK

HAZARD!

Disconnect power

before adjustments,

maintenance, or

service.

INJURY HAZARD!
Do not open door
while machine is
connected to power
or blade is in motion.

G0513 Series

Generic Labels

(7/12/13)

• 1:1 Sizing (Labels are
actual size)
• Labels must be made of
oil-resistant material

To reduce risk of death

or serious injury, read

manual BEFORE using

machine.
To get a new manual,

call (800) 523-4777 or

go to www.grizzly.com.

WARNING!

INJURY HAZARD!
Do not open door
while machine is
connected to power
or blade is in motion.

191

195

197

To reduce risk of death

or serious injury, read

manual BEFORE using

machine.
To get a new manual, call

(800) 523-4777 or go to

www.grizzly.com.

Содержание EXTREME G0513X2





































































































Результаты поиска

Содержание EXTREME G0513X2

Отзывы:

Похожие инструкции для EXTREME G0513X2

Бренды по названию

Популярные бренды

Grizzly EXTREME G0513X2, Руководство пользователя

Результаты поиска

Содержание EXTREME G0513X2

Отзывы:

Похожие инструкции для EXTREME G0513X2

Бренды по названию

Популярные бренды