Grizzly EXTREME G0513X2 Скачать руководство пользователя страница 54

Страница: 54 / 100

-52-

G0513 Series Bandsaws (Mfd. Since 08/22)

Changing Blade

Speed

The blade speed can be adjusted to 1700 or 3500
FPM. Speed adjustments are made by moving the
V-belt position on the motor and wheel pulleys.

Most woodcutting can be performed successfully
at the higher blade speeds. Slower blade speeds
generally produce better results when cutting
hardwoods, intricate curves, or when an excep-
tionally smooth cut is desired.

Use the chart below as a general guide to

blade speed:

Type of Cutting Operation

Blade Speed

(FPM)

Most Species of Wood

3500

Super Dense Hardwood

1700

Fast/Average Feed Rate

3500

Requires Slow Feed Rate

1700

Rough Edges Acceptable

3500

Requires Smooth Edges

1700

Quick, Production Cuts

3500

Detailed, Intricate Cuts

1700

Figure 76. Motor mount cap screws.

3. Refer to Figure 77 to locate the correct V-belt

position for the desired blade speed and
move the V-belt to the indicated pulleys.

3500 FPM

1700 FPM

BANDSAW

WHEEL

MOTOR

WHEEL

Figure 77. V-belt speeds.

Bandsaw

Wheel

⁄

Deflection

Motor

Wheel

Figure 78. V-belt deflection.

4. Rotate the motor to tension the V-belt, then

tighten the motor mount cap screws.

5. Check the V-belt tension by applying mod-

erate pressure between the pulleys (see

Figure 78). If deflection is not approximately

⁄

", re-tension the V-belt until it is.

Tool Needed

Qty

Hex Wrench 8mm .............................................. 1

To adjust the blade speed:

1. DISCONNECT MACHINE FROM POWER!

2. Loosen motor mount cap screws (see Figure

76), and rotate motor to loosen the V-belt.

Содержание EXTREME G0513X2





































































































Результаты поиска

Содержание EXTREME G0513X2

Отзывы:

Бренды по названию

Популярные бренды

Grizzly EXTREME G0513X2, Руководство пользователя

Результаты поиска

Содержание EXTREME G0513X2

Отзывы:

Бренды по названию

Популярные бренды