Thank you for selecting this quality Griot's Garage product. Your T
ornador
® B
lack
P
neumaTic
c
leaning
T
ool
has been engineered
and manufactured to meet Griot's Garage's high standards for dependability, ease of operation, and operator safety. When properly
cared for, it will give you years of trouble-free performance.
PLEASE READ ALL INSTRUCTIONS & SAVE FOR FUTURE REFERENCE
Carefully read through this entire owner's manual before using your T
ornador
® B
lack
P
neumaTic
c
leaning
T
ool
. Pay close attention
to the Safety Requirements, Useful Directions, Air Requirements, Warnings, and Care & Maintenance sections. If you use your Cleaning
Tool properly and only for what it is intended, you will enjoy years of safe, reliable service.
USEFUL DIRECTIONS
Always test a small inconspicuous area to ensure chemical being used will not alter the appearance of the material you are cleaning.
CLEANING FABRIC
1. Remove large debris and vacuum area to be cleaned.
2. With air hose disconnected, remove sprayer/lid from supply cup. Add Griot’s Garage Interior Cleaner to reservoir. Secure sprayer/
lid to reservoir and connect air supply.
3. Turn liquid valve to vertical position; using a smooth overlapping motion, spray area to be cleaned from the bottom up. Allow
the Interior Cleaner to dwell on the surface 10-15 seconds. For severe contamination, gently scrub fabric with Griot’s Garage Ergo
Wave Foam Scrubber or Nylon Carpet & Upholstery Brush.
4. Follow with an application of air only, by turning valve to horizontal position. Begin with smooth overlapping motion followed
with a wipe, using Griot’s Garage Micro Fiber Interior Cloth.
CLEANING DASHBOARD AND HARD SURFACES (FOR USE ON PLASTIC, VINYL & LEATHER)
1. Recommended air pressure set @ 78 psi.
2. With air hose disconnected, remove sprayer/lid from supply cup. Add Griot’s Garage Interior Cleaner to reservoir. Secure sprayer/
lid to reservoir and connect air supply.
3. Protect sensitive components with a towel to prevent inadvertent exposure. (Electrical components, monitors & clear plastics)
4. Turn liquid valve to vertical position, using a smooth overlapping motion, spray area to be cleaned. Follow with an application of
air only, by turning valve to horizontal position. Afterward, wipe down using a Griot’s Garage Micro Fiber Interior Cloth.
WHEEL CARE
1. Clean one wheel at a time. Pre-rinse cool wheel with strong spray of water. (Wheel must not be hot.)
2. Set air pressure set @ 78 psi.
3. With air hose disconnected, remove sprayer/lid from supply cup. Add Griot’s Garage Heavy-Duty Wheel Cleaner or Wheel
Cleaner to clean reservoir. Secure sprayer/lid to reservoir and connect air supply.
4. Turn liquid valve to vertical position; using a smooth overlapping motion, spray area to be cleaned from the bottom up. Allow the
Heavy-Duty Wheel Cleaner or Wheel Cleaner to dwell on the surface for a minute. For severe contamination, gently scrub wheel
with Griot’s Garage Ergo Wave Foam Scrubber, Three-Finger Detail Mitt, Long-Reach Brushes, or Micro Fiber Wand. Rinse wheel
with clean water until runoff is clear.
ENGINE CLEANING
1. Ensure vehicle is not running. Make sure engine bay is warm to the touch. Pre-rinse with high pressure water.
2. Set air pressure @ 78 psi.
3. With air hose disconnected, remove sprayer/lid from supply cup. Add Griot’s Garage Engine Cleaner to clean reservoir. Secure
sprayer/lid to reservoir and connect air supply.
4. Turn liquid valve to vertical position; using a smooth overlapping motion, spray area to be cleaned. Move tool closer to surface to
blast away harsh contaminants and further from surface for light contaminant or delicate areas. For severe contamination gently
scrub surface with Griot’s Garage Ergo Wave Foam Scrubber, Boar’s Hair Detailing Brush, Micro Fiber Wheel Wands, Bendable
Wheel Brush, or other tool. Rinse surface with water or wipe dry with clean micro fiber cloth.
T
ornador
®
B
lack
P
neumaTic
c
leaning
T
ool
