Page 2
WIRING
•
Deactivate the 24 Vac/dc power supply until all connections are made to the device to prevent equipment damage.
•
Use 14-22 AWG shielded wiring for all connections and do not locate the device wires in the same conduit with wiring used to supply
inductive loads such as motors. Make all connections in accordance with national and local codes.
•
The temperature transmitter comes with the temperature sensor pre-wired to the transmitter board. If removal is required for installation
then it may be re-wired as shown in Figure 6.
•
Pull at least six inches of control wire into the enclosure, then complete the wiring connection according to the wire diagram for the
applicable power supply and output signal type as shown in Figure 7.
•
Connect the DC positive or the AC voltage hot side to the PWR terminal. For voltage output or AC power, the supply Common is connected
to the COM terminal. The device is reverse voltage protected and will not operate if connected backwards. It has a half-wave power supply
so the supply Common is the same as the signal Common. See Figure 7.
•
The analog output is available on the OUT terminal. Check the controller Analog Input to determine the proper connection before applying
power as shown in Figure 7.
•
Once all connections are made and checked, power can be applied.
PRINTED IN C
ANAD
A
2 wire temperature sensor wiring to transmitter
NEG
SEN
EXC
NEG
SEN
EXC
3 wire temperature sensor wiring to transmitter
Sense (Green)
Excitation (Red)
Negative (Black)
Excitation (Gray)
No Polarity
Negative (Gray)
No Polarity
Wiring for 0-5 or 0-10 Vdc output
signal and 24 Vdc power from
controller
Wiring for all output signals with
external 24 Vac power transformer
24 Vdc Power Supply
Wiring for 4-20 mA loop-powered
output and external 24 Vdc power
supply
Wiring for 4-20 mA loop-powered
output and external 24 Vdc power
from controller
Transmitter Wiring to Controller
Wiring for 0-5 or 0-10 Vdc output
signal and with external 24 Vdc
power supply
24 Vdc Power Supply
Figure 6
Figure 7
SPECIFICATIONS
:
Sensor Type: .............................................1000Ω Platinum, IEC 751, 385 Alpha, thin film
Sensor Accuracy: ...................................
RTD Class A:
±0.15°C (±0.27°F) @ 0°C (32°F)
RTD 1/3 DIN:
±0.1°C (±0.18°F) @ 0°C (32°F)
RTD 1/10 DIN:
±0.03°C (±0.054°F) @ 0°C (32°F)
Probe Sensing Range: .........................-20 to 100°C (-4 to 212°F)
Wire Material: ..........................................FT-4, 22 AWG
Probe Material: .......................................Aluminum plate with compressible foam backing
Probe Dimensions: ...............................38 mm (1.5") square
Pipe Strap: .................................................25.4 mm (10") stainless steel
Output Signal:.........................................4-20 mA current loop, 0-5 Vdc, or 0-10 Vdc
(factory configured)
Transmitter Accuracy: .........................±0.1% of span, including linearity
Output Drive @ 24 Vdc: ................
Current:
600Ω maximum
Voltage:
10 KΩ minimum
Power Supply: ..................................
0-5 Vdc:
10-35 Vdc or 10-28 Vac
0-10 Vdc:
15-35 Vdc or 15-28 Vac
4-20 mA:
15-35 Vdc (Loop-powered) or 22-28 Vac
Current Consumption: ..................
Current:
20 mA
Voltage:
5 mA
Maximum Current (Voltage): ..........5 mA nominal
Maximum Output (Voltage): ...........Limited to <5.5 Vdc for 0-5 Vdc, <10.5 Vdc for 0-10 Vdc
Input Voltage Effect: ............................Negligible over specified operating range
Protection Circuitry: .............................Reverse voltage protected and output limited
Ambient Operating Range: ..............-40 to 50°C (-40 to 122°F), 0 to 95 %RH non-condensing
Enclosure: ..................................................
A:
ABS, UL94-V0, IP65 (NEMA 4X)
E:
Same as A, with thread adapter (1/2" NPT to M16),
and cable gland fitting
Termination: ............................................Screw terminal block (14 to 22 AWG)
Approvals: .................................................CE
Country of Origin: .................................Canada
*This product is factory calibrated and any field adjustment will void the warranty.
DIMENSIONS
82.5 mm
3.25"
69.8 mm
2.75"
82.5 mm
3.25"
52.0 mm
2.05"
28.6 mm
1.125"
0.5" NPT
Compressible Foam
254 mm (10")
S/S Pipe Clamp
Quick Release
38.1 mm (1.5")
Aluminum Plate
IN-GE-HATXSOXXX-02
Copyright © Greystone Energy Systems, Inc. All Rights Reserved Phone: +1 506 853 3057 Web: www.greystoneenergy.com
