GREER Company MICROGUARD 434, Руководство по калибровке

Страница: 21 / 39

GREER COMPANY
GREER COMPANY GREER COMPANY
GREER COMPANY
Crane Systems Crane Systems Crane Systems Crane Systems
GREER COMPANY 1918 EAST GLENWOOD PLACE SANTA ANA, CALIFORNIA 92705 PN W453201A 08/10/00
MicroGuard
®
434/500 CALIBRATION MANUAL TEL: 714) 259-9702 FAX: 714) 259-7626
21
OF
39
COMMAND 05 MAIN BOOM RADIUS/MOMENT COMMAND 05 MAIN BOOM RADIUS/MOMENT COMMAND 05 MAIN BOOM RADIUS/MOMENT COMMAND 05 MAIN BOOM RADIUS/MOMENT
SECOND LENGTH SECOND LENGTH SECOND LENGTH SECOND LENGTH
MAINTAIN THE SAME HI
MAINTAIN THE SAME HI MAINTAIN THE SAME HI
MAINTAIN THE SAME HIGH ANGLE AND EXTEND
GH ANGLE AND EXTEND GH ANGLE AND EXTEND
GH ANGLE AND EXTEND THE BOOM TO 50% OF E
THE BOOM TO 50% OF E THE BOOM TO 50% OF E
THE BOOM TO 50% OF EXTENSION
XTENSION XTENSION
XTENSION
OR TO THE FULL E
OR TO THE FULL E OR TO THE FULL E
OR TO THE FULL EXTENSION
XTENSION XTENSION
XTENSION
IF THE BOOM MODE EXT
IF THE BOOM MODE EXT IF THE BOOM MODE EXT
IF THE BOOM MODE EXTENDS LESS THEN 30 FE
ENDS LESS THEN 30 FE ENDS LESS THEN 30 FE
ENDS LESS THEN 30 FEET, MEASURE THE NEW
ET, MEASURE THE NEW ET, MEASURE THE NEW
ET, MEASURE THE NEW RADIUS.
RADIUS. RADIUS.
RADIUS.
1.
STORE THE HIGH ANGLE DATA. ......................................................................................................................
1 11 1
2.
USE THE NUMBER ENTRY ROUTINE TO ENTER THE NEW RADIUS.
THE DISPLAY WILL READ: BAS. 1 (U).
MAINTAIN THE SAME LE MAINTAIN THE SAME LE MAINTAIN THE SAME LE MAINTAIN THE SAME LENGTH AND LOWER THE B NGTH AND LOWER THE B NGTH AND LOWER THE B NGTH AND LOWER THE BOOM TO THE OOM TO THE OOM TO THE OOM TO THE LOWEST ANGLE LOWEST ANGLE LOWEST ANGLE LOWEST ANGLE
LISTED ON THE LOAD C LISTED ON THE LOAD C LISTED ON THE LOAD C LISTED ON THE LOAD CHART FOR A FULLY EXT HART FOR A FULLY EXT HART FOR A FULLY EXT HART FOR A FULLY EXTENDED BOOM. ENDED BOOM. ENDED BOOM. ENDED BOOM.
IF THE CRANE HAS 0° IF THE CRANE HAS 0° IF THE CRANE HAS 0° IF THE CRANE HAS 0° CAPABILITIES, LOWER CAPABILITIES, LOWER CAPABILITIES, LOWER CAPABILITIES, LOWER THE BOOM TO 5°. MEAS THE BOOM TO 5°. MEAS THE BOOM TO 5°. MEAS THE BOOM TO 5°. MEASURE THE NEW RADIUS. URE THE NEW RADIUS. URE THE NEW RADIUS. URE THE NEW RADIUS.
3.
STORE THE LOW ANGLE DATA. ......................................................................................................................
1 11 1
4
. USE THE NUMBER ENTRY ROUTINE TO ENTER THE NEW RADIUS.
THE DISPLAY WILL READ BAS. 1 (D U).
5.
START THE MOMENT CALIBRATION AT THE CURRENT LENGTH. .............................................................
1
11
1
6
. CONFIRM OR ABORT THE CALIBRATION.
.............................................................
1
1 1
1
YES
/3
/3 /3
/3
ABORT
7.
EXIT THE ROUTINE. ...........................................................................................................................................
6
66
6
OR REPEAT THE ABOVE FOR UP TO 7 LENGTHS.
Continue the calibration routine with Command 06, BDC. If there is a Manual section or Mode B on the crane,
return to Command 05
after completing the BDC for the Main Boom.
REVIEW THE SAMPLE DISPLAY SCREEN ON PAGE 4 REVIEW THE SAMPLE DISPLAY SCREEN ON PAGE 4 REVIEW THE SAMPLE DISPLAY SCREEN ON PAGE 4 REVIEW THE SAMPLE DISPLAY SCREEN ON PAGE 4.
Use the designated arrow key (
1, 2, 3, 4, or 6
1, 2, 3, 4, or 6 1, 2, 3, 4, or 6
1, 2, 3, 4, or 6
) appearing to the right of each step
when ENTERING or EXITING a COMMAND
and to CHOOSE, START, CONFIRM, ABORT, RESET, or ENTER an action.