Cleaning
Cleaning the Output Port
Cleaning all connectors before coupling them to the 170XL visual fault
finder will ensure proper maintenance of the output port and laser lens.
Users should always cover the output port with the dust cap when the
instrument is not in use.
If binding or stickiness is felt when inserting connectors into the output
port, the ceramic sleeve should be cleaned. To clean the sleeve, insert a
Tempo 946 cleaning wand into the output port until it stops. Twist the
wand, remove it, and discard. Do not reuse the cleaning wand.
Cleaning the Laser Lens
If the intensity of the light output decreases considerably, despite the
batteries being in good condition, the laser lens is probably dirty. Loose
dirt can be removed by applying suction to the output port.
NOTE: Do not blow air into the output port to remove dirt particles. Doing
so will only pack the dirt and make it harder to remove.
If the lens is extremely dirty, flush out the output port with a
small amount of reagent-grade isopropyl alcohol, then apply
gentle suction to remove any remaining dirt. Make sure that all
residual alcohol has evaporated before resuming testing.
Specifications
Light source
635nm red laser diode and monitor,
with multi-quantum well structure
Central wavelength:
Nominal
635nm
Range (typical)
630nm to 640nm
Spectral width
< 2nm
Peak power output
1, 2, 3
:
Into SMF-28 fiber, CW or
1.0mW (0dBm) maximum
MOD output mode
316µW (-5dBm) minimum
Maximum emitted power
2.0mW
MOD output frequency
< 3Hz, approximate
Power requirements
Two (2) 1.5V alkaline batteries
Battery life
Approx. 48 hrs. continuous operation
Connector interface
2.5mm “quick connect” port
2
,
or 16-series SOC adapters
CDRH
Class IIIa
Environmental:
Operating temperature
-10°C to +50°C
Storage temperature
-40°C to +60°C
Humidity
0 to 95% RH, non-condensing
Weight and dimensions
22.9 x 2.54cm (9 x 1 in.)
200g (7 oz) with batteries and pouch
1 Within specified ambient environment of +20°C to +25°C.
2 APC-type ferrule coupling efficiency reduced by > -3dBm.
3 Output power with beam collimator may exceed 1mW. Product complies with CDRH Class II, 1mW
max. without collimator accessory and IEC 825-1: 1993, 5mW max.
EC Declaration of Conformity
We,
Greenlee Textron Inc.
4455 Boeing Drive
Rockford, IL 61109-2988
U.S.A
declare under sole responsibility that the 170XL visual fault finder laser
source, manufactured in the United States of America, meets the intent
of the directive 89/336/EEC for electromagnetic compatibility. Compliance
was demonstrated to the following specifications as listed in the official
Journal of the European Communities:
EN 50081-1, Emissions: EN 55022
Radiated, Class B
EN 55022
Conducted, Class B
EN 60555-2
Power Harmonics
EN 50082-1, Immunity:
IEC 801-2
Electrostatic Discharge
IEC 801-3
RF Radiated
IEC 801-4
Fast Transients
IEC 801-5
Surge
Warranty Information
Greenlee warrants this product to be free from defects in material and
workmanship for a period of one (1) year from the date of shipment.
During the warranty period we will, at our option, either repair or
replace any product that proves to be defective. To exercise this warranty,
write or call your local Greenlee representative, or contact Greenlee
directly.
You will be given prompt assistance and return instructions. Send the
instrument, transportation prepaid, to the indicated service facility.
Repairs will be made and the instrument will be returned, transportation
prepaid. Repaired products are warranted for the balance of the original
warranty period, or at least 90 days.
Limitation of Warranty
This warranty does not apply to defects resulting from unauthorized
modification or misuse of any product or part. This warranty is in lieu of all
other warranties, expressed or implied, including any implied warranty of
merchantability or fitness for a particular use. Greenlee shall not be liable
for any indirect, special, or consequential damages.
Notice of Proprietary Rights
The design concepts and engineering details embodied in this manual,
which are the property of Greenlee, are to be maintained in strict
confidence.
No element or detail of this manual is to be spuriously used, nor disclosed
without the express written permission of Greenlee. All rights are reserved.
No part of this publication may be reproduced, stored in a retrieval system,
or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without prior written permission
from Greenlee.
COPYRIGHT © 2005 BY GREENLEE
ALL RIGHTS RESERVED. FIRST EDITION 2005
PRINTED IN THE UNITED STATES OF AMERICA
Greenlee Textron Inc.
4455 Boeing Drive
Rockford, IL 61109-2988
U.S.A
www.greenlee.textron.com
USER MANUAL
170XL
VISUAL FAULT FINDER
97-0170-67 Rev A