Greenheck ERCH-20 Скачать руководство пользователя страница 1

®

Installation, Operation and Maintenance Manual

Please read and save these instructions for future reference. Read carefully before attempting to assemble, install, 
operate or maintain the product described. Protect yourself and others by observing all safety information. Failure 
to comply with instructions could result in personal injury and/or property damage!

Energy Recovery Ventilator with Heating and Cooling

1

®

Only qualified personnel should install this system. 
Personnel should have a clear understanding of these 
instructions and should be aware of general safety 
precautions. Improper installation can result in electric 
shock, possible injury due to coming in contact with 
moving parts, as well as other potential hazards, 
including environmental. Other considerations may be 
required if high winds or seismic activity are present. 
If more information is needed, contact a licensed 
professional engineer before moving forward.

1

.  Follow all local electrical and safety codes, as well as 

the National Electrical Code (NEC), the National Fire 
Protection Agency (NFPA), where applicable. Follow 
the Canadian Electrical Code (CE) in Canada.

2.  All moving parts must be free to rotate without 

striking or rubbing any stationary objects.

3.  Unit must be securely and adequately grounded.
4.  Do not spin fan wheel faster than maximum 

cataloged fan RPM. Adjustments to fan speed 
significantly affect motor load. If the fan RPM is 
changed, the motor current should be checked to 
make sure it is not exceeding the motor nameplate 
amps.

5.  Verify that the power source is compatible with the 

equipment.

6.  Never open access doors to the unit while it is 

running.

General Safety Information

DANGER

•  Always disconnect power before working on or near 

this equipment. Lock and tag the disconnect switch 
or breaker to prevent accidental power up.

•  If this unit is equipped with optional gas 

accessories, turn off gas supply whenever power is 
disconnected.

CAUTION

This unit may be equipped with a compressed 
refrigerant system. If a leak in the system should 
occur, immediately evacuate and ventilate the area. 
An EPA Certified Technician must be engaged to 
make repairs or corrections. Refrigerant leaks may 
also cause bodily harm.

CAUTION

When servicing the unit, the internal components may 
be hot enough to cause pain or injury. Allow time for 
cooling before servicing.

WARNING

The roof lining contains high voltage wiring. To 
prevent electrocution, do not puncture the interior or 
exterior panels of the roof.

Document 476054

Model ERCH

Energy Recovery Ventilator

with Heating and Cooling 

Содержание ERCH-20

























































Отзывы: