background image

Multi Variable Air Conditioners One-way Cassette Type Indoor Unit 

10 

4.2 Refrigerant Pipe Connection 

(1)  Aim the flaring port of copper pipe at the center of screwed joint and then tighten the flaring nut 

with hand as shown in Fig.4.2. 

(2)  Tighten the flaring nut with torque wrench. 

 

Fig.4.2 

Pipe diameter(mm) 

Torque(N•m) 

6.35 

15~30 

9.52 

35~40 

12.7 

45~50 

15.9 

60~65 

(3)  Use pipe bend when bending the pipe and the bending angle should not be too small.   
(4)  Wrap the connection pipe and joint with sponge and then tie them firmly with tape. 

4.3 Drainage Pipe Installation and Drainage System Testing 

4.3.1 Notice for Installation of Drain Pipe 

(1)  It is not allowed to connect the condensate drain pipe into waste pipe or other pipelines which 

are likely to produce corrosive or peculiar smell to prevent the smell from entering indoors or 
corrupt the unit. 

(2)  It is not allowed to connect the condensate drain pipe into rain pipe to prevent rain water from 

pouring in and cause property loss or personal injury. 

(3)  Condensate drain pipe should be connected into special drain system for air conditioner. 
(4)  The drainage pipe should be short and the gradient downwards should be at least 1%~2% in 

order to drain condensation water smoothly. 

(5)  The diameter of drainage hose should be bigger or equal to the diameter of drainage pipe joint. 
(6)  Install drainage pipe according to the following Fig and arrange insulation to the drainage pipe. 

Improper installation may lead to water leakage and damp the furniture and other things in the 
room.   

(7)  You can buy normal hard PVC pipe used as the drainage pipe. During connection, insert the 

end of PVC pipe into the drainage hole and then tighten it with drainage hole and wire binder. 
Can’t connect the drainage hole and drainage hole with glue. 

(8)  When the drainage pipelines are used for several units, the position of pipeline should be about 

100mm lower than the drainage port of each unit. In this case, thicker pipes should be applied. 

Содержание GMV-ND22TD/A-T




























Отзывы: