Gree GMV-ND22C/A-T Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 30

background image

Multi Variable Air Conditioners Console Type Indoor Unit

5

2.2 Refrigerant Piping

(1) Drill a hole (65mm in diameter) in the spot indicate

d by О the symb

ol in the illustration and

below.

(2)  The location of the hole is different depending on which side of the pipe is taken out.
(3)  For piping, see Connecting the refrigerant pipe, under Indoor Unit Installation.
(4)  Allow space around the pipe for an easier indoor unit pipe connection.

CAUTION!

Min. allowable length.
The suggested shortest pipe length is 2.5m, in order to avoid noise from the outdoor unit and

vibration (Mechanical noise and vibration may occur depending on how the unit is installed and the
environment in which it is used).

See the installation manual for the outdoor unit for the maximum pipe length.
For multi-connections, see the installation manual for the multi-outdoor unit.

«
...
7
8
9
10
11
...
»

Содержание GMV-ND22C/A-T































Отзывы:

Нет отзывов

Похожие инструкции для GMV-ND22C/A-T

Бренд: Samsung Страницы: 52

Бренд: Samsung Страницы: 35

AC TN4PKG Series

Бренд: Samsung Страницы: 20

Бренд: Carrier Страницы: 104

Бренд: York Страницы: 25

Optimum YW09H2/I

Бренд: Yamato Страницы: 15

UNI AIR PURIFIER 02

Бренд: UNIPRODO Страницы: 19

Бренд: Crosley Страницы: 4

Бренд: NEO TOOLS Страницы: 51

GWH09ACC-S6DBA1A/O

Бренд: Gree Страницы: 123

Бренд: Daikin Страницы: 68

Бренд: York Страницы: 20

Бренд: MICAN Страницы: 292

Бренд: Zamil Страницы: 16

Бренд: Perfect Aire Страницы: 28

Brio-I SLIM IVR 10

Бренд: RHOSS Страницы: 76

Бренд: Olimpia splendid Страницы: 28

Бренд: INVENTOR Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды