Gree CB385001000 страница 74 Скачать руководство пользователя

Страница: 74 / 136

Installation and Maintenance

Service Manual

9.2 Procedure of Troubleshooting

Indoor unit

1. Malfunction of Temperature Sensor

Main detection points:

● Is the wiring terminal between the temperature sensor and the controller loosened or poorly contacted?
● Is there short circuit due to trip-over of the parts?
● Is the temperature sensor broken?
● Is mainboard broken?

Malfunction diagnosis process:

Is the wiring terminal between the

temperature sensor and the controller

loosened or poorly contacted?

Start

Insert the temperature

sensor tightly

Yes

Is malfunction

eliminated

Is malfunction

eliminated

Is malfunction

eliminated

Replace it with a

temperature sensor with

the same model

Make the parts upright

Is there short circuit due to trip-

over of the parts

Is the temperature sensor normal

according to the resistance table?

Replace the mainboard with

the same model.

End

Содержание CB385001000









































































































































Результаты поиска

Содержание CB385001000

Отзывы:

Похожие инструкции для CB385001000

Бренды по названию

Популярные бренды

Gree CB385001000, Руководство по обслуживанию

Результаты поиска

Содержание CB385001000

Отзывы:

Похожие инструкции для CB385001000

Бренды по названию

Популярные бренды