background image

Champaign, Illinois

(217) 398-8970, Ext 5

[email protected]

Entire Contents © Copyright 2010

GPMA1875 Mnl

READ THROUGH THIS MANUAL BEFORE STARTING CONSTRUCTION. IT CONTAINS IMPORTANT

INSTRUCTIONS AND WARNINGS CONCERNING THE ASSEMBLY AND USE OF THIS MODEL.

WARRANTY

Great Planes

®

 Model Manufacturing Co. guarantees this kit to 

be free from defects in both material and workmanship at the 
date of purchase. This warranty does not cover any component 
parts damaged by use or modification. In no case shall Great 
Planes’ liability exceed the original cost of the purchased kit.
 
Further, Great Planes reserves the right to change or modify this 
warranty without notice.

In that Great Planes has no control over the final assembly or 
material used for final assembly, no liability shall be assumed nor 
accepted for any damage resulting from the use by the user of 
the final user-assembled product. By the act of using the 
user-assembled product, the user accepts all resulting liability.

If the buyer is not prepared to accept the liability associated 
with the use of this product, the buyer is advised to return 

this kit immediately in new and unused condition to the 
place of purchase.

To make a warranty claim send the defective part or item to 
Hobby Services at the address below:

Hobby Services

3002 N. Apollo Dr.  Suite 1

Champaign IL  61822  USA

Include a letter stating your name, return shipping address, as 
much contact information as possible (daytime telephone 
number, fax number, e-mail address), a detailed description of 
the problem and a photocopy of the purchase receipt. Upon 
receipt of the package the problem will be evaluated as quickly 
as possible.

Length:

37 in [940mm]

Battery:

2200mAh 14.8V 25C LiPo

Radio:

3-Channel minimum with
two mini servos & mini Rx

Motor,

ESC

24-45-3790kV Ammo

,

45A ESC

Wingspan:

22.5 in
[565mm]

Wing Area:

162 in

2

[10.4 dm

2

Weight:

26.8 oz
[760 g]

Wing

Loading:

23.8 oz /ft

2

[73 g /dm

2

]

SPECIFICATIONS

INSTRUCTION MANUAL

Length:

37 in [940mm]

Radio:

3-Channel minimum with
two mini servos & mini Rx

Motor

24 45 3790kV Ammo

Wingspan:

22.5 in
[565mm]

Weight:

26.8 oz
[760 g]

SPECIFICATIONS

INSTRUCTION MANUAL

STRUCTIO

TRUCTION MANUAL

EDF ARF

EP

Содержание EP F-20 Tigershark ElectriFLy

















Отзывы: