manualshive.com logo in svg

GREAT PLAINS Ultra-Till I 3030 Series, Руководство оператора

Поделиться
Скачать
GREAT PLAINS Ultra-Till I 3030 Series Скачать руководство пользователя страница 17

UT3030-UT5052

Table of Contents

Index

Preparation and Setup

Great Plains

 | 576-026M-A | 05/11/2021

Table of Contents

Index

15

Hitching Tractor to Ultra-Till

Crushing Hazard:

Do not  stand or place any body  part between Ultra-Till and

moving tractor. You may be severely injured or killed by being

crushed between the tractor and Ultra-Till. Stop tractor engine

and set parking brake before attaching cables and hoses.

To  prevent  soil  compaction  on  rows,  set  tractor  wheels

between rows. For hillsides and steep slopes, set tractor wheels

as wide as possible for maximum stability.
1. Raise  tractor  three-point  arms  (if  equipped)  clear  up  to

clear Ultra-Till.

2. For  TWO-WHEEL  DRIVE  and  MFWD  tractors,  pin

drawbar  in  fixed  center position  for  field  and  transport.

For FOUR-WHEEL DRIVE and TRAC-DRIVE tractors,

leave one hole clearance on each side of drawbar for field

position, hitch damage may occur if pinned solid. Pin in

center  position  for  transport  to  maintain  maximum

steering control.

3. Hitch the tractor to the Ultra-Till using the block or yoke

clevis determined by the tractor drawbar.This machine is

equipped  with  a  reversible  single  tang  hitch.  Use  the

correct size hitch pin to insure proper performance and to

minimize wear.

Load Sway Hazard:

Lock drawbar swing to center position to minimize any side-to-

side sway to assure proper tracking in the field, and safe road 

travel. See 

“

Transporting

” on page 18

, for safe 

transporting

Refer to Figure 3
4. Use jack (1) to raise and lower Ultra-Till tongue.
Refer to Figure 4
5. After hitching tractor to Ultra-Till, store jack on storage

tube (2) on top of hitch strut.

6. Secure Ultra-Till safety chain to an anchor on the tractor

capable of pulling the unit.

Figure 3

Tongue on Jack

43184

1

2

Figure 4

 Jack in Storage

43182

Содержание Ultra-Till I 3030 Series





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды