manualshive.com logo in svg

GREAT PLAINS Terra Max HT1110-6.0M, Руководство оператора

Поделиться
Скачать
GREAT PLAINS Terra Max HT1110-6.0M Скачать руководство пользователя страница 22

Great Plains

 | 588-206M | 3/21/22

Table of Contents

18

HT1110-6.0M & 7.5M

Table of Contents

First Time Field Adjustments

Gang Cylinders

Gang Angle Adjustment

Check gang angle adjustment when machine is new

and annually after, as wear may occur.
15.With front gang adjusting cylinders (1) in the full 

retract position the gang bar (2) should be 

1

8

” 

from tubes (3).

16. If gang bar (2) is not 

1

8

” from tubes (3) loosen allen screw

(4)  on  clevis  on  rod  end  of  cylinder  (there  are  two  flat

spots  on  rod  to  get  wrench  on  to  adjust)  and  shorten

cylinder rod (5) by turning cylinder rod to bring gang bar

closer and lengthen clevis to get cylinder to retract all the

way.

17. Re-tighten allen screw (4) when adjustment is made.

Note the two different turnbuckles used. One is on the

center frame and the other is used on the wings. They

function in the same way.
18.When the front gang adjusting cylinders (1), have 

been adjusted and are in the full retract position 

the rear gang bar (6) should be parallel to back 

frame tube.

19. If  rear  gang  bar  (6)  is  not  parallel  to  back  frame  tube,

remove  pin  (7)  from  turnbuckle  end  (8)  and  shorten

turnbuckle end by turning clevis to bring gang bar closer

and lengthen clevis to get gang bar to retract all the way.

20. Re-install pin (7) after adjustment is made.

1

4

5

3

2

7

6

8

6

7

8

Содержание Terra Max HT1110-6.0M











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды