manualshive.com logo in svg

GREAT PLAINS Terra Max HT1110-6.0M, Руководство оператора

Поделиться
Скачать
GREAT PLAINS Terra Max HT1110-6.0M Скачать руководство пользователя страница 15

HT1110-6.0M & 7.5M

Table of Contents

Adjustments and Installation

Great Plains

 | 588-206M | 3/21/22

Table of Contents

11

Hitching Terra Max to Tractor

Hitch  to  a  tractor  for  highway  transport  and  field  operations.

Before  hitching,  check  the  compatibility  and  capability  of  the

towing tractor:
For  hillsides  and  steep  slopes,  set  tractor  wheels  as  wide  as

possible for maximum stability.
1. Raise tractor three-point arms (if equipped) all the way up to

clear Terra Max.

2. For TWO-WHEEL DRIVE and MFWD tractors, pin drawbar

in  fixed  center  position  for  field  and  transport.  For  FOUR-

WHEEL DRIVE and TRAC-DRIVE tractors, leave one hole

clearance  on  each  side  of  drawbar  for  field  position,  hitch

damage may occur if pinned solid. Pin in center position for

transport to maintain maximum steering control.

3. Use jack (1) to raise and lower Terra Max tongue.
4. Back tractor draw bar into alignment with hitch (2).
5. Secure with a locking hitch pin.
6. Secure safety chain to an anchor on the tractor.

Negative Tongue Weight Hazard:

Make certain that Terra Max is securely hitched to the tractor or

leading  implement  before. An unhitched  Terra  Max  can  tip  over

backwards during hitching if the tongue is not secured.

7. Retract jack foot. Re-orient jack to storage position.
8. After  hitching  tractor  to  Terra  Max,  store  jack  on  storage

stub (4) on the tongue.

Load Sway Hazard:

Lock drawbar swing to center position to minimize any

side-to-side sway to assure proper tracking in the field,

and  safe  road travel. See  “

Transport

” on  page 24, for

safe transporting.

Crushing Hazard:

Do not stand or place any body part between Terra Max

and moving tractor. You may be severely injured or killed

by  being  crushed  between  the  tractor  and  Terra  Max.

Stop  tractor  engine  and  set  parking  brake  before

attaching cables and hoses.

1

2

4

Содержание Terra Max HT1110-6.0M











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды