GREAT PLAINS Nutri-Pro NP30A Скачать руководство пользователя страница 97

Страница: 97 / 172

NP30A or NP40A

Table of Contents

Index

Adjustments

2019-03-11

Table of Contents

Index

407-502M

Unfold Stop Adjustment

This applies to 2103+ 5-Section applicators only.

Refer to Figure 70

During unfold (FOLD / FIELD switch in FOLD), the inner

wing sections are intended to stop 0 to 5° above

wings-level relative to the center section . The stopping

point is controlled by a vertical proximity sensor

each center/wing hinge. If a wing does not stop in this

range, adjust the proximity sensor.
1. Verify that the misalignment is not caused by air in

the hydraulic system. Do not use the proximity

adjustment to compensate for hydraulic problems.

2. Move the applicator to a level surface. Raise and fold

(page 62). Install lift-assist lock channels (page 45)

and parking stands (page 36).

3. Set the FOLD / FIELD switch to FOLD. Extend the

fold/lift circuit to unfold until the inner wings stop.

Set the circuit to Neutral. Shut off the tractor.

4. Check the sensor-actuator (

) gap at the

affected wing pivot. With the actuator near the

marked region on the sensor, the gap must be:

inch (3.2 to 6.3 mm)

If the gap is incorrect, correct that, at the current

sensor height. Fold and unfold to see if further

adjustment is required.

5. To adjust the sensor, loosen the bolts securing the

sensor

to the bracket. Do not adjust the

actuator

position.

To lower the angle at which the wing stops, raise the

sensor.

To raise the angle at which the wing stops, lower the

sensor.

6. Secure the bolts. Fold and unfold to test.

Figure 70

Unfold Stop Proximity Sensor

34991

20 7

Содержание Nutri-Pro NP30A













































































































































































Результаты поиска

Содержание Nutri-Pro NP30A

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS Nutri-Pro NP30A, Руководство оператора

Результаты поиска

Содержание Nutri-Pro NP30A

Отзывы:

Бренды по названию

Популярные бренды