manualshive.com logo in svg

GREAT PLAINS Nutri-Pro NP30A, Руководство оператора

Поделиться
Скачать
GREAT PLAINS Nutri-Pro NP30A Скачать руководство пользователя страница 71

NP30A or NP40A

Table of Contents

Index

Applicator Operating Instructions

67

2019-03-11

Table of Contents

Index

407-502M

Transport Steps

Know your applicator weight. See page 136 or page 139

for tables including approximate weights of

representative configurations.
If tractor capabilities are marginal, check the actual

weight of the applicator at a scale.

Pull-Type Applicators

1. Check that applicator is securely hitched to a

sufficient tractor (page 30).

2. Always use a locking-style hitch pin sized to match

holes in hitch and draw-bar (minimum

1-inch-diameter, heat-treated pin).

3. Attach safety chain to tractor with enough slack to

permit turning (page 30).

4. Verify correct operation of lights. 
5. Raise fertilizer applicator (page 51).
6. Install center and lift-assist cylinder locks (page 45).
7. Fold applicator if unfolded (page 59).
8. Check that tires are properly inflated (page 140).
9. Plan the route. Avoid steep hills.
10. Always have lights on for highway operation.
11. Do not exceed 32 kph (20 mph). Comply with all

national, regional and local laws when traveling on

public roads. 

12. Remember that the applicator may be wider than the

tractor. Allow safe clearance.

13. Transport slowly over uneven or rough terrain.
14. At field, stop transport with the tractor facing

up-wind.

2-Point and 3-Point Applicators

1. Check that fertilizer applicator is securely hitched to

a sufficient tractor (page 31)

2. Verify correct operation of lights.
3. Raise fertilizer applicator (page 53).
4. Install cylinder locks (2-point, page 45).
5. Fold applicator if unfolded (page 59).
6. Plan the route. Avoid steep hills.
7. Always have lights on for highway operation.
8. Do not exceed 32 kph (20 mph). Comply with all

national, regional and local laws when traveling on

public roads. 

9. Remember that the fertilizer applicator may be wider

than the tractor. Allow safe clearance.

10. Transport slowly over uneven or rough terrain.
11. At field, stop transport with the tractor facing

up-wind.

Final Applicator Setup

Prior to hitching nurse tank, make and check final

applicator adjustments. This could include:

• Application depth, page 96:

2-Point, page 38, page 86 and tractor hitch

3-Point, page 86 and tractor hitch

Pull-Type, page 85

• Coulter (Option) depth and castering, page 99.

• Knife or tine condition, page 100.

• Sealer (Option) adjustments, page 102.

• Make a dry run to check applicator functions, running

depth and sealing.

For nurse cart hitching, the applicator may be raised or

lowered, folded or unfolded. However, being raised and

folded hastens departure if any nurse tank problems are

discovered before cart hitching. 

Содержание Nutri-Pro NP30A













































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды