GREAT PLAINS Nutri-Pro NP30A Скачать руководство пользователя страница 53

Страница: 53 / 172

NP30A or NP40A

Table of Contents

Index

Applicator Operating Instructions

2019-03-11

Table of Contents

Index

407-502M

2013+ NP40A 2-Point Fold/Lift Circuit

On 2-point 5-section NP40A applicators made in 2013 or

later, the fold and lift cylinders share a single hydraulic

circuit. Solenoid valves (controlled by a switch box), one

or more passive valves, and mechanical locks control

hydraulic sequencing.
This system design provides a partial fold, as a single

self-limiting hydraulic operation, during field lift, providing

extra wing clearance in field turns.
If the hydraulic harness is not connected at the hitch, or

the switch box is off, or power is off, most valves default

to an Open state.

FOLD / FIELD Switch

Refer to Figure 31 (depicting the switch in PARK)

This switch is mounted in the tractor cab (page 157), and

connected to the applicator at the hitch. It controls

several solenoid valves on the applicator. It has three

toggle positions and two indicator lamps.
Note: The switch is powered by the tractor. An illuminated

lamp indicates power sent to the harness. The

harness must be connected at the hitch for the

function to be effected.

Switch Positions

PARK

All solenoid valves are powered off and are

spring-loaded to flow-open positions.

Use this position only for parking, to save tractor

battery power. With the switch in PARK, any

hydraulic flow to the fold/lift circuit may have

undesired results.

FOLD
UNFOLD

Full fold and unfold sequence is controlled.

Down-pressure is disabled.

During unfold, the inner wings unfold before the

outer wings. During fold, the outer wings fold before

the inner wings. Fold range from fully folded to

wings level (excepting down-pressure) is available.

FIELD

Outer wings locked.

Inner wing fold restricted to “gull wing”.

Down-pressure available.

Use this position in the field. It engages the

down-pressure circuit for weight transfer.

It provides a partial fold for extra wing clearance in

field turns.

Figure 31

FOLD / FIELD Switch

34918

Machine Damage Risks:

Lift/lower (except field lift) and fold/unfold operations are
possible with the hydraulic harness off, but care must be

exercised. It is possible to lower below level, which can result

in row unit ground strikes and dragging.

Содержание Nutri-Pro NP30A













































































































































































Результаты поиска

Содержание Nutri-Pro NP30A

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS Nutri-Pro NP30A, Руководство оператора

Результаты поиска

Содержание Nutri-Pro NP30A

Отзывы:

Бренды по названию

Популярные бренды