GREAT PLAINS 6000 Series Скачать руководство пользователя страница 8

Страница: 8 / 36

6000 Series

Table of Contents

Index

Great Plains Manufacturing, Inc.

562-094M

Table of Contents

Index

2015-01-05

Practice Safe Maintenance

▲

Understand procedure before doing work. Use proper tools
and equipment. Refer to this manual for additional
information.

▲

Work in a clean, dry area.

▲

Lower the implement, put tractor in park, turn off engine,
and remove key before performing maintenance.

▲

Make sure all system pressure is relieved.

▲

Disconnect battery ground cable (-) before servicing or
adjusting electrical systems or before welding on
implement.

▲

Inspect all parts. Make sure parts are in good condition and
installed properly.

▲

Remove buildup of grease, oil or debris.

▲

Remove all tools and unused parts from implement before
operation.

Safety At All Times

Thoroughly read and understand the instructions in this
manual before operation. Read all instructions noted on
the safety decals.

▲

Be familiar with all implement functions.

▲

Operate machinery from the driver’s seat only.

▲

Do not leave implement unattended with tractor engine
running.

▲

Do not dismount a moving tractor. Dismounting a moving
tractor could cause serious injury or death.

▲

Do not stand between the tractor and implement during
hitching.

▲

Keep hands, feet and clothing away from moving parts.

▲

Watch out for wires, trees, etc., when folding and raising
implement. Make sure all persons are clear of working area.

Содержание 6000 Series





































Результаты поиска

Содержание 6000 Series

Отзывы:

Похожие инструкции для 6000 Series

Бренды по названию

Популярные бренды

GREAT PLAINS 6000 Series, Руководство оператора

Результаты поиска

Содержание 6000 Series

Отзывы:

Похожие инструкции для 6000 Series

Бренды по названию

Популярные бренды