GREAT PLAINS 3S-4000HD Скачать руководство пользователя страница 24

Страница: 24 / 118

Great Plains Manufacturing, Inc.

Table of Contents Index

Preparation and Setup

2019-03-14

Table of Contents Index

195-067M

Older Color Hose Ties

Refer to Figure 11

On older drillsm to distinguish hoses on the same

hydraulic circuit, refer to plastic hose label. The hose

under an extended-cylinder symbol feeds a cylinder

base end. The hose under a retracted-cylinder symbol

feeds a cylinder rod end.
Great Plains hydraulic hoses are color coded to help you

hookup hoses to your tractor outlets.Hoses that go to the

same remote valve are marked with the same color.

1. Connect opener-lift hoses to circuit designated for

hydraulic-motor control.

2. Connect transport-lift hoses to tractor remote valve.
3. Connect fold hoses to tractor remote valve.
4. Connect marker hoses to tractor remote valve.
Note: If your tractor has only two remote valves, you must

install a double-selector valve to combine the

transport-lift and opener-lift circuits. See “

Two

Outlet Hydraulic Kit

” on page 98.

Check Drill Level

These items are set and verified at the factory or by your

dealer, but need to be checked prior to first use.
• “

Center Box Frame Leveling

” on page 80

• “

Opener Frames

” on page 80

• “

Wing Box Alignment

” on page 81

• “

Align Transfer Drive Shaft

” on page 82

• “

Truss Tube Tension

” on page 84

• “

Tool Bar Height

” on page 84

• “

Opener-Frame Clearance

” on page 85

Color

Hydraulic Function

Red

Opener Lift Cylinders

Blue

Transport Lift Cylinders

White

Fold Cylinders

Orange

Marker Cylinders

Equipment Damage Risk:

To run drill on tractors with open-center hydraulics or on

tractors with fixed-displacement hydraulic pumps, you must

install a Great Plains kit, part number 194-143A. If you are
not familiar with your tractor hydraulics, consult your tractor

dealer.

Figure 11

Plastic Hose Label

817-348c

17641

Содержание 3S-4000HD























































































































Результаты поиска

Содержание 3S-4000HD

Отзывы:

GREAT PLAINS 3S-4000HD, Руководство оператора, Страница: 24 / 118

Результаты поиска

Содержание 3S-4000HD

Отзывы: