GREAT PLAINS 3S-4000 Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 126

GREAT PLAINS 3S-4000 Скачать руководство пользователя страница 78

2018-06-19

Table of Contents

195-442M

3S-4000, 3S-4000F, 3S-4000HD, 3S-4000HDF

Table of Contents

Maintenance and Lubrication

74

Maintenance and Lubrication

Proper servicing and maintenance is the key to long
implement life. With careful and systematic inspection,
you can avoid costly maintenance, downtime and repair.

Always turn off and remove the tractor key before making
any adjustments or performing any maintenance.

Crushing Hazard:

You may be severely injured or killed by being crushed under a
falling implement. Always have frame sufficiently blocked up
when working on, and particularly under implement.

High Pressure Fluid Hazard:

Only trained personnel should work on system hydraulics!
Check all hydraulic lines and fittings before applying
pressure. Relieve pressure before disconnecting hydraulic
lines. Wear protective gloves and safety glasses or goggles
when working with hydraulic systems. Fluid escaping from a
very small hole can be almost invisible. Use paper or
cardboard, NOT BODY PARTS, to check for leaks. Escaping
fluid under pressure can have sufficient pressure to penetrate
the skin causing serious injury. If hydraulic fluid is injected
into the skin or eyes, seek immediate medical assistance from a
physician familiar with this type of injury. Within a few hours
gangrene can start to develop. DO NOT DELAY.

After using drill for several hours, check all bolts to be
sure they are tight.

1.

Securely block drill before working on it.

2.

Lubricate areas listed under “

Lubrication and

Scheduled Maintenance

” on page 92.

3.

Remove excess slack from chains. Clean and use
chain lube on all roller chains as needed.

4.

Clean any fittings that do not take grease.

5.

Inflate tires as specified on “

Tire Inflation Chart

6.

Inspect hydraulic hoses for cuts, cracks and aging.
Check fittings for evidence of leaks.

7.

Keep disk scrapers properly adjusted.

8.

Replace any worn, damaged or illegible safety
decals. Order new decals from your Great Plains
dealer. “

Safety Decals

«
...
76
77
78
79
80
...
»

Содержание 3S-4000































































































































Отзывы:

Нет отзывов