GREAT PLAINS 3S-4000 Скачать руководство пользователя страница 74

Страница: 74 / 126

2018-06-19

Table of Contents

Index

195-442M

3S-4000, 3S-4000F, 3S-4000HD, 3S-4000HDF

Table of Contents

Index

Troubleshooting

Problem

Cause

Solution

Planting too much

Incorrect seed rate or drive type.

Check seed rate information in Seed Rate
Manual.

Seed size and weight may vary.

Adjust seed rate handle.

Actual field size is different.

Verify field size.

Excessive overlap.

Irregular shaped field.

Adjust marker, page 25.

Incorrect tire size or air pressure.

Correct tire size and air pressure,
page 106.

Seed cup door open too much.

Refer to Seed Rate Manual.

Planting too little

Incorrect seed rate or drive type.

Check seed rate information in Seed Rate
Manual.

Excessive field speed.

Reduce field speed.

Seed size and weight may vary.

Adjust seed rate handle.

Incorrect tire size or air pressure.

Correct tire size and air pressure,
page 106.

Check seed level in seed box.

Fill seed box.

Actual field size is different.

Verify field size.

Excessive gaps between drill passes.

Adjust marker, page 25.

Build up of seed treatment in seed cups.

Clean out seed cups.

Plugged opener seed tube.

Lift drill, expose bottom of seed tube and
clean out.

Obstruction in seed cup from foreign matter
or unclean seed.

Clean seed cup.

Thrown or worn drive chains

Check drive chains.

Worn sprockets and/or chain idlers.

Replace sprockets and/or chain idlers.

Uneven seed depth

Excessive field speed.

Reduce field speed.

Planting conditions too wet.

Wait until drier weather.

Seed-Lok

building up with dirt.

Lock up Seed-Lok

, page 62.

Damaged or missing seed flaps.

Replace seed flaps.

Partially plugged opener seed tube.

Lift up drill, expose bottom of seed tube
and clean out.

Содержание 3S-4000































































































































Результаты поиска

Содержание 3S-4000

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS 3S-4000, Руководство оператора

Результаты поиска

Содержание 3S-4000

Отзывы:

Бренды по названию

Популярные бренды