manualshive.com logo in svg

GREAT PLAINS 3S-4000, Руководство оператора

Поделиться
Скачать
GREAT PLAINS 3S-4000 Скачать руководство пользователя страница 31

3S-4000, 3S-4000F, 3S-4000HD, 3S-4000HDF

Table of Contents

Index

Operating Instructions

27

2018-06-19

Table of Contents

Index

195-442M

Raising and Lowering Openers

Negative Tongue Weight Hazard:

Raising openers on unfolded, unhitched drill will cause drill
tongue to rise suddenly, which could cause serious injury or
death. Be certain that drill is hitched securely to your tractor
draw bar and the safety chain is securely attached to tractor
before raising openers and unfolding drill.

Opener sub-frames are on a dedicated hydraulic circuit.
Openers raise and lower independently of the drill frame
(which is raised and lowered by the transport lift circuit).

When lowered, the opener circuit can use live hydraulic
power to regulate down pressure. To operate with live
hydraulic power, connect the opener lift circuit to the #1
remote hydraulic circuit or the circuit designed for
HYDRAULIC MOTOR control. On many CLOSED
CENTER or PRESSURE/FLOW COMPENSATED
tractors the #1 circuit is the circuit designed to supply live
hydraulic power to remote locations.

On the standard 3S-4000/F/HD/HDF drill, the openers
raise and lower as a group, from a tractor cab lever. If the
Point Row Option is installed, each section can raise and
lower independently, using switches on the point row
control module in the tractor cab.

If the Two Outlet conversion kit is installed, a selector
valve near the hitch must be operated to switch between
Opener Lift and Transport Lift. During field operations,
this valve is in the Opener Lift position.

Opener Lock Up

The openers must be locked up for transporting or for
working under the drill.

Refer to Figure 15

Each opener lift assembly has wire rod lock handle

,

and a cylinder lock status indicator

 on the lock hook.

Opener transport lock handles

 can be moved with

openers up or down, but transport locks only engage
after openers are raised completely and disengage
after openers are lowered completely. There are two
lock handles on each drill section, six handles total.

Lock Up Openers

1.

Position opener transport handles in ROAD position.

2.

Raise openers completely.

Unlock Openers

Refer to Figure 15

1.

Position opener transport lock handles in FIELD
position.

2.

Raise openers completely.

Figure 15

Opener Lock-Up

15549

2

1

Figure 16

Opener Unlock

15548

1

2

1

Содержание 3S-4000































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды