GREAT PLAINS 3S-4000 Скачать руководство пользователя страница 21

Страница: 21 / 126

3S-4000, 3S-4000F, 3S-4000HD, 3S-4000HDF

Table of Contents

Index

Introduction

2018-06-19

Table of Contents

Index

195-442M

Intended Usage

Use this implement to seed production-agriculture
crops in conventional or minimum tillage applications.

Using This Manual

This manual familiarizes you with safety, assembly,
operation, adjustments, troubleshooting, and
maintenance. Read this manual and follow the
recommendations to help ensure safe and efficient
operation.

The information in this manual is current at printing.
Some parts may change to assure top performance.

Definitions

The following terms are used throughout this manual.

Right-hand and left-hand as used in this manual are
determined by facing the direction the machine will travel
while in use unless otherwise stated.

Paragraphs in Notice format present a crucial point of
information related to the current topic.

Read and follow the directions to:
- remain safe,
- avoid serious damage to equipment and
- ensure desired field results.



Paragraphs in Note format provide useful information
related to the current topic.

Figure 2

Left/Right Notation

18824

Содержание 3S-4000































































































































Результаты поиска

Содержание 3S-4000

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS 3S-4000, Руководство оператора

Результаты поиска

Содержание 3S-4000

Отзывы:

Бренды по названию

Популярные бренды