manualshive.com logo in svg

GREAT PLAINS 3S-3000HD, Руководство оператора

Поделиться
Скачать
GREAT PLAINS 3S-3000HD Скачать руководство пользователя страница 84

80

3S-3000HD

Table of Contents Index

Great Plains Manufacturing, Inc.

195-068M

Table of Contents Index

2019-03-12

Opener-Frame Clearance

Refer to Figure 88

When fully raised, top of opener mounts   should clear 
bottom of drill frame tube by at least 

1

2

 inch (12.7mm).

To adjust opener frames so all openers have the same 
clearance, loosen jam nut   on opener lift cylinders and 

turn adjustment nut. When openers are at the correct 

height, retighten jam nut. Repeat at each opener lift 

cylinder if necessary.

Marker Maintenance

Marker Transport Carrier

When marker is folded, the second section should be 

centered in transport carrier saddle and be parallel with 

top of drill box. 

Refer to Figure 89

To adjust height of saddle, loosen 

1

2

x2in U-bolts   that 

hold carrier tube to mounting bracket. Slide carrier tube 

up or down as needed.

Marker Shear Bolt

The marker arm is attached to marker body with a shear 
bolt  , which is intended to fail if the marker strikes an 

obstruction, allowing the marker to swing back around a 
second bolt  .
If the shear bolt breaks, replace it with an equivalent 

3

18

-16x2in Grade 2 bolt (Great Plains part 802-266C). If 

that size is not available in your local market, temporarily 

substitute an M10x1.5 Class 5.8 metric bolt and nut.
Note: Replacing the bolt with a lower grade, or smaller 

size, can result in nuisance shears.

Equipment Damage Risk:

Replacing the bolt with a higher grade can result in marker 

damage.

FigureSpacer

Figure 88

Opener Frame Clearance

18853

2

1

1

2

FigureSpacer

Figure 89

Marker Transport Carrier

15632

1

1

2

3

FigureSpacer

Figure 90

Marker Shear Bolt

15669

2

3

Содержание 3S-3000HD





















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды