GREAT PLAINS 3S-3000HD Скачать руководство пользователя страница 80

Страница: 80 / 116

3S-3000HD

Table of Contents Index

Great Plains Manufacturing, Inc.

195-068M

Table of Contents Index

2019-03-12

Wing Box Alignment

1. Place a block ahead of the wing gauge wheels.

Refer to Figure 80

2. Pull forward against blocks to rock wing frames

back. Pull forward until stop bolts are firmly

against toolbars.

Refer to Figure 81

3. Check for proper alignment by running a string line

across back of drill toward outer ends of wings.

Make sure string is parallel to center box (both mea-
surements

equal).

4. For proper alignment, outside ends of boxes

should be about 1in to 1



in (2.5 to 3.2cm) ahead of

inside ends .

5. To adjust box alignment, shorten or lengthen stop

bolts to change the contact point with the toolbars.

Loosen jam nut and thread stop bolt in or out. Adjust

stop bolts in or out until outside ends of boxes are
1in to 1



in (2.5 to 3.2cm) ahead of inside ends.

6. Tighten jam nut.

FigureSpacer

Figure 80

Stop Bolt Location

18988

FigureSpacer

Figure 81

Wing Box Alignment Measurement

15654

Содержание 3S-3000HD





















































































































Результаты поиска

Содержание 3S-3000HD

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS 3S-3000HD, Руководство оператора

Результаты поиска

Содержание 3S-3000HD

Отзывы:

Бренды по названию

Популярные бренды