GREAT PLAINS 3S-3000HD Скачать руководство пользователя страница 77

Страница: 77 / 116

Great Plains Manufacturing, Inc.

Table of Contents Index

Maintenance and Lubrication

2019-03-12

Table of Contents Index

195-068M

Bleeding Marker Hydraulics

Crushing and Sharp Object Hazard:

You may be injured if hit by a folding or unfolding marker.
Markers may fall quickly and unexpectedly if the hydraulics

fail. Never allow anyone near the drill when folding or unfold-

ing markers.

1. Review warnings, bleeding notes and system infor-

mation on page 69.

Refer to Figure 75

2. With markers unfolded in field position, crack

hydraulic-hose JIC fittings at base and rod ends of

each marker cylinder.

3. With tractor at idle speed, activate tractor hydraulic

valve forward until oil appears at a fitting. When oil

begins to seep out around a fitting, tighten that fitting.

Reverse the tractor hydraulic valve until oil appears

at opposite hose fitting. Tighten that fitting.

4. If you have dual markers, activate tractor hydraulic

valve forward again until oil seeps out around a fit-

ting on the other marker cylinder. Tighten that fitting.

Reverse tractor hydraulic valve until oil seeps out

around remaining hose fitting and tighten it.

5. Fold and unfold markers slowly to work out all air.
Note: Use caution when folding and unfolding markers

for the first time, checking for pinching and kinking

of hoses.

In-Line Filters

If the raising or lowering times of the openers slow

noticeably, check the in-line filters and clean if needed.

Refer to Figure 76

Two filters are located on one each of the down-pressure

adjustment valves. If the Point Row option is installed,

another filter is located on the third adjustment valve

FigureSpacer

Figure 75

Bleeding Marker Hydraulics

18942

FigureSpacer

Figure 76

In-Line Filter Locations

22968

Содержание 3S-3000HD





















































































































Результаты поиска

Содержание 3S-3000HD

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS 3S-3000HD, Руководство оператора

Результаты поиска

Содержание 3S-3000HD

Отзывы:

Бренды по названию

Популярные бренды