GREAT PLAINS 3S-3000-3210 Скачать руководство пользователя

Страница: 8 / 118

2018-06-18

Table of Contents

Index

195-441M

3S-3000/F/HD/HDF

Table of Contents

Index

Important Safety Information

Handle Chemicals Properly

Agricultural chemicals can be dangerous. Improper use
can seriously injure persons, animals, plants, soil and
property.



Do not use liquid treatments with drill.



Read and follow chemical manufacturer’s instructions.



Wear protective clothing.



Handle all chemicals with care.



Avoid inhaling smoke from any type of chemical fire.



Never drain, rinse or wash dispensers within 100 feet
(30m) of a freshwater source, nor at a car wash.



Store or dispose of unused chemicals as specified by
chemical manufacturer.



Dispose of empty chemical containers properly. Laws
generally require power rinsing or rinsing three times,
followed by perforation of the container to prevent re-use.

Shutdown and Storage



Clean out and safely store or dispose of residual
chemicals.



Secure drill using blocks and transport locks. Lower
openers if not locked up.



Store in an area where children normally do not play.

Practice Safe Maintenance



Understand procedure before doing work. Use proper
tools and equipment. Refer to this manual for additional
information.



Work in a clean, dry area.



Put tractor in park, turn off engine, and remove key before
performing maintenance.



Make sure all moving parts have stopped and all system
pressure is relieved.



Disconnect battery ground cable (-) before servicing or
adjusting electrical systems or before welding on drill.



Inspect all parts. Make sure parts are in good condition
and installed properly.



Remove buildup of grease, oil or debris.



Remove all tools and unused parts from drill before
operation.

Содержание 3S-3000-3210























































































































Результаты поиска

Содержание 3S-3000-3210

Отзывы:

Похожие инструкции для 3S-3000-3210

Бренды по названию

Популярные бренды

GREAT PLAINS 3S-3000-3210, Руководство оператора

Результаты поиска

Содержание 3S-3000-3210

Отзывы:

Похожие инструкции для 3S-3000-3210

Бренды по названию

Популярные бренды