GREAT PLAINS 3S-3000-3210 Скачать руководство пользователя | Manualshive

Страница: 5 / 118

background image

2018-06-18

Table of Contents

195-441M

3S-3000/F/HD/HDF

Table of Contents

Important Safety Information

1

Important Safety Information

Look for Safety Symbol

The SAFETY ALERT SYMBOL indicates there is a
potential hazard to personal safety involved and extra
safety precaution must be taken. When you see this
symbol, be alert and carefully read the message that
follows it. In addition to design and configuration of
equipment, hazard control and accident prevention are
dependent upon the awareness, concern, prudence and
proper training of personnel involved in the operation,
transport, maintenance and storage of equipment.

Be Aware of Signal Words

Signal words designate a degree or level of hazard
seriousness.

DANGER indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.
This signal word is limited to the most extreme situations,
typically for machine components that, for functional
purposes, cannot be guarded.

WARNING indicates a potentially hazardous situation
which, if not avoided, could result in death or serious
injury, and includes hazards that are exposed when
guards are removed. It may also be used to alert against
unsafe practices.

CAUTION indicates a potentially hazardous situation
which, if not avoided, may result in minor or moderate
injury. It may also be used to alert against unsafe
practices.

Prepare for Emergencies



Be prepared if a fire starts



Keep a first aid kit and fire extinguisher handy.



Keep emergency numbers for doctor, ambulance, hospital
and fire department near phone.

Be Familiar with Safety Decals



Read and understand “

Safety Decals

” on page 6,

thoroughly.



Read all instructions noted on the decals.



Keep decals clean. Replace damaged, faded and illegible
decals.

«
...
3
4
5
6
7
...
»

Содержание 3S-3000-3210























































































































Отзывы:

Нет отзывов

Похожие инструкции для 3S-3000-3210

Origo Feed 304 PIPE

Бренд: ESAB Страницы: 44

Бренд: John Shearer Страницы: 40

Pasture Renovation Drill

Бренд: John Shearer Страницы: 59

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды