GREAT PLAINS 2S-2600 Скачать руководство пользователя страница 51

Страница: 51 / 114

2S-2600/F/HD/HDF

Table of Contents

Index

Operating Instructions

Great Plains

| 195-440M | 2019-05-03

Table of Contents

Index

Storage

Store the drill where children do not play. If possible,

store it inside for longer life.
1. Perform the drill Parking checklist.
2. Lubricate the drill at all points listed under

“

Lubrication

” on page 81.

3. Check all bolts, pins, fittings and hoses. Tighten,

repair or replace parts as needed.

4. Check all moving parts for wear or damage. Make

notes of any parts needing repair before the next

season.

5. Raise and lock up openers.

Raise and lock up Transport lift.

Fold drill.

Do not lower openers with drill folded.

6. Thoroughly clean drill boxes and seed cups. Do not

store drill with fertilizer or seed-treatment residue in

boxes and cups.

7. Plug or cap seed delivery and fertilizer tubes to

prevent pest entry.

8. Lock opener frames up for transport or disconnect

seed and fertilizer hoses from openers. Leaving

seed hoses connected when storing drill with

openers lowered will cause permanent stretching

and cracking of hoses.

9. Use touch-up paint to cover scratches, chips and

worn areas to prevent rust.

Содержание 2S-2600



















































































































Результаты поиска

Содержание 2S-2600

Отзывы:

GREAT PLAINS 2S-2600, Руководство оператора, Страница: 51 / 114

Результаты поиска

Содержание 2S-2600

Отзывы: