GREAT PLAINS 2S-2600 Скачать руководство пользователя страница 50

Страница: 50 / 114

Great Plains

| 195-440M | 2019-05-03

Table of Contents

Index

2S-2600/F/HD/HDF

Table of Contents

Index

Operating Instructions

Parking

Following these steps when parking for less than 36

hours. For longer periods, see

Storage

, the next topic.

Parking with Drill Unfolded

This drill has a negative tongue weight when unfolded and
openers are raised. Lower parking stand, lower openers and

remove hydraulic down pressure before unhitching the drill in

the unfolded position. Unhitching in the unfolded position with
the openers raised could result in sudden elevation of the

tongue, causing injury or death.

1. Remove jack from storage location on top of tongue

and pin it on post on left side of tongue as shown on

page 17. Extend jack until weight of tongue is on

jack. Leave tractor hitched for the moment.

Refer to Figure 46 and Figure 47

2. Lower parking stands located on outer ends of drill

by unpinning keeper pin and rotating stands down.

Place a block under foot of stand if it does not

contact the ground.

3. Lower openers and reduce hydraulic down pressure

to zero.

4. Unplug drill hydraulic hoses and electrical lines from

tractor.

Use caution when removing the hitch pin. Slight tongue

elevation may occur, even with openers and parking stands

lowered.

5. Remove hitch pin first, then safety chain from tractor

drawbar.



NOTE:

After unhitching the unfolded drill, the tongue may rise

above tractor-drawbar height. Lower tongue by

connecting the opener-lift circuit and pressurizing

openers.

Parking with Drill Folded

1. Raise, lock and fold drill into transport position.
2. Park drill on a level, solid area.
3. Remove tongue jack from its storage location on top

of tongue and pin it on post on left side of tongue as

shown on page 17. Extend jack until weight of

tongue is on jack. If ground is soft, place a board or

plate under jack to widen ground-contact area.

4. Unplug hydraulic hoses and electrical lines from

tractor.

5. Remove hitch pin first, then safety chain from tractor

drawbar.

Figure 46

Wing Stand Pinned Up

36269

Figure 47

Wing Stand Pinned Down

36270

Содержание 2S-2600



















































































































Результаты поиска

Содержание 2S-2600

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS 2S-2600, Руководство оператора

Результаты поиска

Содержание 2S-2600

Отзывы:

Бренды по названию

Популярные бренды