GREAT PLAINS 2S-2600 Скачать руководство пользователя страница 36

Страница: 36 / 114

Great Plains

| 195-440M | 2019-05-03

Table of Contents

Index

2S-2600/F/HD/HDF

Table of Contents

Index

Operating Instructions

Lowering Drill (Transport Lift)

Lowering from Transport Lift may be done only when the

drill is unfolded.
Transport Lift is on a dedicated hydraulic circuit. The

main frame raises and lowers independently of the

opener sub-frames (which are raised and lowered by the

Opener Lift circuit).

Transport Lower

1. Unfold drill. See “

Unfolding

” on page 31.

2. If the Two Outlet conversion kit is installed, confirm

that the selector valve, located near the hitch, is set

for Transport Lift operations. See “

Lift Selector

Valve Operation

” on page 43.

3. Slowly extended the Transport Lift circuit lever until

both Transport Lift circuit cylinders are fully

extended. Set circuit lever to off or neutral (not float).

Refer to Figure 28

4. Rotate cylinder lock channels down and forward off

transport lift cylinders.

5. Slowly reverse the lift circuit lever and begin lowering

the drill. Keep the circuit engaged until both cylinders

are completely retracted. Set circuit to off or neutral.

Figure 28

Transport Lift Cylinder Lock

18960

Содержание 2S-2600



















































































































Результаты поиска

Содержание 2S-2600

Отзывы:

Похожие инструкции для 2S-2600

Бренды по названию

Популярные бренды

GREAT PLAINS 2S-2600, Руководство оператора

Результаты поиска

Содержание 2S-2600

Отзывы:

Похожие инструкции для 2S-2600

Бренды по названию

Популярные бренды