manualshive.com logo in svg

GREAT PLAINS 2N-2410, Руководство оператора

Поделиться
Скачать
GREAT PLAINS 2N-2410 Скачать руководство пользователя страница 49

8/2/18

Table of Contents

Index

196-126M

2N-2410 & 2N-3010

Table of Contents

Index

Troubleshooting

46

Cylinder Lock Channels

The cylinder lock channels

 are 1 1/2 in wide

channels. They are pinned to the bottom edges of the
mainframe near the tongue, one on each side. When
performing maintenance operations, the cylinder lock
channels

 must be installed on the field-lift cylinder

rods

. During transport the cylinder lock channels

must be installed in the storage location on the
mainframe. 

The cylinder lock channel must not contact the lower depth
stop assembly or damage will occur.

The cylinder lock channels must not be installed on the
field-lift cylinder rods during transport or damage can occur.

To install a cylinder lock channel on the left-hand
transport cylinder, do the following:

1.

Remove the bolt

, lock washer, and nut from the

lower depth stop assembly

.

2.

Rotate the lower depth stop assembly down.

3.

Install the cylinder lock channel on the transport
cylinder rod.

4.

Install the clevis pin

 and hair pin in the cylinder

lock channel.

Storage

Store the drill where children do not play. If possible,
store the drill inside for longer life.

1.

If you store the drill in the unfolded position, unpin
and fully retract the fold cylinders to prevent rust.

2.

Clean the drill as necessary. Be sure

 

that the seed

boxes are cleaned completely before storing. 

3.

Disconnect seed hoses from openers. Premature hose
damage will occur if drill is stored with hoses connected.

4.

Adjust idlers to remove excess slack from chains.
Adjust gauge-wheel-arm drive chain as explained
under 

Gauge-Wheel Drive Adjustment

, page 39. Clean

and use chain lube on all roller chains as needed.

5.

Lubricate the drill at all points indicated under

Lubrication

, this page.

 

Be sure the seed-cup drive

sprocket is oiled before the drill is stored. 

6.

Check all bolts, pins, fitting and hoses. Tighten,
repair or replace parts as needed.

7.

Check all moving and soil-contact parts for wear or
damage. Make notes of any parts needing repair.

8.

Use Great Plains touch-up paint to cover scratches,
chips and worn areas to prevent rust.

1

5

2

3

4

Figure 33

Pull Cable

1

1

2

3

4

5

Содержание 2N-2410

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды